Difficulty

Moderate

Steps

41

Time Required

                          20 - 30 minutes

Sections

1

  • OnePlus 7 Pro Screen Replacement
  • 41 steps

Flags

2

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackOnePlus 7 Pro

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Before disassembling your device, be sure the battery is charged below 25%. If accidentally punctured or damaged, the battery can catch fire and/or explode; if discharged below 25%, the chances of fire/explosion are decreased.

Be sure to power off the device before beginning the disassembly process.

Follow the iOpener Heating guide for instructions on using the iOpener.

What you need

Video Overview

Step 1

              OnePlus 7 Pro Screen Replacement
  • Insert and gently push the SIM card ejector tool (or an unfolded paperclip) into the small hole on the left side of the top edge of the phone.
  • Press gently to eject the SIM tray.
  • Remove the SIM card tray from the device.
  • To reinsert the SIM card tray, orient the SIM card with the gold contacts facing up and the notch to the bottom right. Reinsert the SIM card by pressing the card gently into the SIM tray slot.

Insert and gently push the SIM card ejector tool (or an unfolded paperclip) into the small hole on the left side of the top edge of the phone.

Press gently to eject the SIM tray.

Remove the SIM card tray from the device.

To reinsert the SIM card tray, orient the SIM card with the gold contacts facing up and the notch to the bottom right. Reinsert the SIM card by pressing the card gently into the SIM tray slot.

1024

Step 2

  • Use a heat gun to lightly heat the edges of the back to soften the adhesive that connects the back cover to the rest of the frame.
  • Using a heat gun, hair dryer, or hot plate will make the metal frame rather hot to the touch, so handle it with care.
  • Be careful not to overheat the device –the OLED display, battery and other internal parts can be damaged by excessive heat. Approximately one minute should be enough to soften the adhesive.
  • An iFixit iOpener, hairdryer, or hot plate can also be used to heat the edges. See the iOpener Heating guide for instructions on using the iOpener.

Use a heat gun to lightly heat the edges of the back to soften the adhesive that connects the back cover to the rest of the frame.

Using a heat gun, hair dryer, or hot plate will make the metal frame rather hot to the touch, so handle it with care.

Be careful not to overheat the device –the OLED display, battery and other internal parts can be damaged by excessive heat. Approximately one minute should be enough to soften the adhesive.

An iFixit iOpener, hairdryer, or hot plate can also be used to heat the edges. See the iOpener Heating guide for instructions on using the iOpener.

Step 3

  • Apply a suction cup to the lower portion of the phone’s backing and pull firmly to create a crack between the back cover and the rest of the phone.
  • Insert a Jimmy tool, opening pick, or plastic card under the edge of the back cover.

Apply a suction cup to the lower portion of the phone’s backing and pull firmly to create a crack between the back cover and the rest of the phone.

Insert a Jimmy tool, opening pick, or plastic card under the edge of the back cover.

Step 4

  • Use a plastic card or Jimmy tool to slice around the phone’s seam, cutting through the adhesive.

Use a plastic card or Jimmy tool to slice around the phone’s seam, cutting through the adhesive.

Step 5

  • Remove the phone’s back cover.
  • If you have replacement adhesive strips, remove any remaining adhesive from the device frame using the Jimmy tool.

Remove the phone’s back cover.

If you have replacement adhesive strips, remove any remaining adhesive from the device frame using the Jimmy tool.

Step 6

  • Use a pair of tweezers to lift up the piece of black tape covering the laser autofocus and flash flex cable.
  • Use a pair of tweezers to lift and remove the covering on the laser autofocus and flash flex cable.

Use a pair of tweezers to lift up the piece of black tape covering the laser autofocus and flash flex cable.

Use a pair of tweezers to lift and remove the covering on the laser autofocus and flash flex cable.

Step 7

  • Use the flat end of a spudger to disconnect the laser autofocus and flash flex cable.

Use the flat end of a spudger to disconnect the laser autofocus and flash flex cable.

Step 8

  • Use a Phillips #000 screwdriver to remove the fourteen screws from the plastic motherboard cover.

Use a Phillips #000 screwdriver to remove the fourteen screws from the plastic motherboard cover.

Step 9

  • Use the flat end of a spudger to lift up the plastic motherboard cover.
  • Remove the plastic motherboard cover.

Use the flat end of a spudger to lift up the plastic motherboard cover.

Remove the plastic motherboard cover.

Step 10

  • Use the flat end of a spudger to disconnect the power flex cable.

Use the flat end of a spudger to disconnect the power flex cable.

Step 11

  • Use the flat end of a spudger to disconnect the longer black coaxial cable.
  • Use the flat end of a spudger to disconnect the white coaxial cable.
  • Use the flat end of a spudger to disconnect the shorter black coaxial cable.

Use the flat end of a spudger to disconnect the longer black coaxial cable.

Use the flat end of a spudger to disconnect the white coaxial cable.

Use the flat end of a spudger to disconnect the shorter black coaxial cable.

Step 12

  • Use the flat end of a spudger to disconnect the display and touch flex cable, main flex cable, and USB port cable.

Use the flat end of a spudger to disconnect the display and touch flex cable, main flex cable, and USB port cable.

Step 13

  • Use the flat end of a spudger to disconnect the black cable on the left-hand side of the phone.

Use the flat end of a spudger to disconnect the black cable on the left-hand side of the phone.

Step 14

  • Use the flat end of a spudger to pry up the long black cable on the left-hand side of the phone.
  • Use the flat end of a spudger to disconnect the end of the long black cable.

Use the flat end of a spudger to pry up the long black cable on the left-hand side of the phone.

Use the flat end of a spudger to disconnect the end of the long black cable.

Step 15

  • Use a pair of tweezers to pry up the red plastic tab.
  • Use a pair of tweezers to remove the assembly connected to the red plastic tab.

Use a pair of tweezers to pry up the red plastic tab.

Use a pair of tweezers to remove the assembly connected to the red plastic tab.

Step 16

  • Use the flat end of a spudger to disconnect the connector that was underneath the red plastic tab.

Use the flat end of a spudger to disconnect the connector that was underneath the red plastic tab.

Step 17

  • Use a Phillips #000 screwdriver to remove the remaining two screws securing the motherboard.

Use a Phillips #000 screwdriver to remove the remaining two screws securing the motherboard.

Step 18

  • Use the flat end of a spudger to lift up the phone’s motherboard.
  • Remove the motherboard.

Use the flat end of a spudger to lift up the phone’s motherboard.

Remove the motherboard.

Step 19

  • Use a Phillips #000 screwdriver to remove two short screws.
  • Use a Phillips #000 screwdriver to remove one screw.

Use a Phillips #000 screwdriver to remove two short screws.

Use a Phillips #000 screwdriver to remove one screw.

Step 20

  • Use a pair of tweezers to remove the camera elevator assembly.

Use a pair of tweezers to remove the camera elevator assembly.

Step 21

  • Lift up the large flex cable with your fingers.
  • Use a pair of tweezers to remove the black plastic screw covering.

Lift up the large flex cable with your fingers.

Use a pair of tweezers to remove the black plastic screw covering.

Step 22

  • Use a Phillips #000 screwdriver to remove two small screws from the metal covering.
  • Remove the metal covering.

Use a Phillips #000 screwdriver to remove two small screws from the metal covering.

Remove the metal covering.

Step 23

  • Use the flat end of a spudger or your fingers to gently remove the front camera assembly.

Use the flat end of a spudger or your fingers to gently remove the front camera assembly.

Step 24

  • Use a Phillips #000 screwdriver to remove one screw in the upper left-hand corner.

Use a Phillips #000 screwdriver to remove one screw in the upper left-hand corner.

Step 25

  • Use a pair of tweezers to disconnect the earpiece’s yellow flex cable.
  • Use a pair of tweezers to remove the earpice.

Use a pair of tweezers to disconnect the earpiece’s yellow flex cable.

Use a pair of tweezers to remove the earpice.

Step 26

  • Use your fingers to pull on the red sticker labelled ‘Pull Up From This Side.’
  • Remove the battery.

Use your fingers to pull on the red sticker labelled ‘Pull Up From This Side.’

Remove the battery.

Step 27

  • Use your fingers to grab the black tab and remove the plastic that was underneath the battery.

Use your fingers to grab the black tab and remove the plastic that was underneath the battery.

Step 28

  • Use a Phillips #000 screwdriver to remove eight screws from the bottom panel.
  • Use the flat end of a spudger to pry up the bottom cover.
  • Remove the bottom cover.

Use a Phillips #000 screwdriver to remove eight screws from the bottom panel.

Use the flat end of a spudger to pry up the bottom cover.

Remove the bottom cover.

Step 29

  • Use the flat end of a spudger to disconnect the fingerprint sensor, the LED flex cable, the CED flex cable, and the display and touch flex cable.

Use the flat end of a spudger to disconnect the fingerprint sensor, the LED flex cable, the CED flex cable, and the display and touch flex cable.

Step 30

  • Use the flat end of a spudger to disconnect the three coaxial cables near the bottom of the phone.
  • To disconnect the longer coaxial cable, you will need to pry the wire from its clips.

Use the flat end of a spudger to disconnect the three coaxial cables near the bottom of the phone.

To disconnect the longer coaxial cable, you will need to pry the wire from its clips.

Step 31

  • Use a Phillips #000 screwdriver to remove one screw.
  • Use the flat end of a spudger to lift up the sub-board.
  • Remove the phone’s sub-board.

Use the flat end of a spudger to lift up the sub-board.

Remove the phone’s sub-board.

Step 32

  • Use a Phillips #000 screwdriver to remove two screws.

Use a Phillips #000 screwdriver to remove two screws.

Step 33

  • Use a pair of tweezers to peel out the black stickers from the sides and bottom of the battery area.

Use a pair of tweezers to peel out the black stickers from the sides and bottom of the battery area.

Step 34

  • Use your fingers to remove the three signal cables.

Use your fingers to remove the three signal cables.

Step 35

  • Use the flat end of a spudger to disconnect the USB port flex cable.

Use the flat end of a spudger to disconnect the USB port flex cable.

Step 36

  • Use your fingers to remove the LED flex cable, CED flex cable, and USB port cable.

Use your fingers to remove the LED flex cable, CED flex cable, and USB port cable.

Step 37

  • Use a pair of tweezers to disconnect the fingerprint sensor.

Use a pair of tweezers to disconnect the fingerprint sensor.

Step 38

  • Remove the vibration sensor using a pair of tweezers.

Remove the vibration sensor using a pair of tweezers.

Step 39

  • Disconnect the coaxial cable in the lower left-hand corner using the flat end of a spudger.

Disconnect the coaxial cable in the lower left-hand corner using the flat end of a spudger.

Step 40

  • Use a Phillips #000 screwdriver to remove two screws on the left-hand side of the phone’s frame.
  • Use a pair of tweezers to remove the plastic piece that was secured with the two previous screws.

Use a Phillips #000 screwdriver to remove two screws on the left-hand side of the phone’s frame.

Use a pair of tweezers to remove the plastic piece that was secured with the two previous screws.

Step 41

  • Remove the coaxial cable using the flat end of a spudger.
  • Remove the coaxial cable from the left-hand side of the battery’s area.

Remove the coaxial cable using the flat end of a spudger.

Remove the coaxial cable from the left-hand side of the battery’s area.

To reassemble your device, install each of the components removed during this guide into a new screen with a frame by following these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 4 other contributors 


                    Selena

Member since: 12/15/2019

2,590 Reputation

                                      14 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Clayton Lawliss - Jul 22, 2020

Reply

So I have a friend that owns this phone and has had the screen replaced, there is however some misalignment of the screen and frame on her phone in the form of a very obvious crack between the two, the two surfaces are also not flush. Could someone in theory have improperly repaired the phone by separating the screen from the frame and gluing a new one in place?

Thank you and have a nice day.

MJ Mulenga III - Jan 7, 2022

Reply

Is it possible to replace just the top glass if the rest of the screen is intact? It’s got surface cracks both front and back.

Joel Tool - Feb 16, 2022

Reply

Absolutely none of this is necessary as they don’t sell the screen with the frame. If you’re unlucky like me you’ll get the entire phone apart and then it will tell you to reassemble parts onto screen WITH frame.

S. S. - Feb 25, 2022

Reply

Could this be used and adapted to replace the charging port?

Daniel Malkowski - Jul 26, 2022

Yes, I got the part on amazon and successfully replaced the charging port as well as the battery when I opened it