Difficulty
Difficult
Steps
13
Time Required
20 minutes - 1 hour
Sections
4
- Back Cover
- 4 steps
- Front Camera
- 4 steps
- Motherboard
- 4 steps
- Rear Camera
- 1 step
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackOnePlus 6T
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Make sure the phone is powered off and placed with the back cover facing towards you on a stable surface.
Make sure the phone is powered off and placed with the back cover facing towards you on a stable surface.
1024
Step 2
- Pop open the SIM card tray by inserting a SIM card removal tool into a small hole on the upper-left side of the phone.
- Carefully remove the SIM card from its tray.
Pop open the SIM card tray by inserting a SIM card removal tool into a small hole on the upper-left side of the phone.
Carefully remove the SIM card from its tray.
Step 3
- Loosen the binding glue within the phone using a hairdryer or an iOpener.
- If you choose to use a hairdryer, hold the dryer at least eight inches from the phone and apply heat for two minutes in a circular motion around the edges of the phone.
Loosen the binding glue within the phone using a hairdryer or an iOpener.
If you choose to use a hairdryer, hold the dryer at least eight inches from the phone and apply heat for two minutes in a circular motion around the edges of the phone.
Step 4
- Insert a Jimmy under one of the heated corners of the phone to lift it slightly.
- Insert a plastic card underneath the slightly lifted lip on the back cover and gently glide the card under the lifted phone casing.
- There will be a small amount of tension, but this is normal as the card is removing the adhesive within the phone.
- Remove the back cover from the phone.
- Use high concentration (>90%) isopropyl alcohol and a lint-free cloth to remove all adhesive residue from the back cover and the frame.
Insert a Jimmy under one of the heated corners of the phone to lift it slightly.
Insert a plastic card underneath the slightly lifted lip on the back cover and gently glide the card under the lifted phone casing.
There will be a small amount of tension, but this is normal as the card is removing the adhesive within the phone.
Remove the back cover from the phone.
Use high concentration (>90%) isopropyl alcohol and a lint-free cloth to remove all adhesive residue from the back cover and the frame.
Step 5
Front Camera
- Remove the single 3mm Phillips #00 screws holding the metal battery cover on the phone.
- Use tweezers to remove the battery cover and place it to the side.
Remove the single 3mm Phillips #00 screws holding the metal battery cover on the phone.
Use tweezers to remove the battery cover and place it to the side.
Step 6
- Remove eight 3mm Phillips #00 screws that connect the midframe to the phone.
Remove eight 3mm Phillips #00 screws that connect the midframe to the phone.
Step 7
- Using a spudger, gently remove the midframe and place it to the side.
Using a spudger, gently remove the midframe and place it to the side.
Step 8
- Using a spudger, lift the light brown tab in the middle of phone to disconnect the front camera.
- Remove the front camera from the phone.
Using a spudger, lift the light brown tab in the middle of phone to disconnect the front camera.
Remove the front camera from the phone.
Step 9
Motherboard
- Remove the single 3mm Phillips #00 screw to the right of the top rear camera.
Remove the single 3mm Phillips #00 screw to the right of the top rear camera.
Step 10
- Using a spudger, disconnect the charging port flex connector, the main flex connector, and the screen flex connector at the bottom of the camera.
Using a spudger, disconnect the charging port flex connector, the main flex connector, and the screen flex connector at the bottom of the camera.
Step 11
- Use a spudger to disconnect the signal cables on the right side of the motherboard.
Use a spudger to disconnect the signal cables on the right side of the motherboard.
Step 12
- Disconnect the slider from the top of the phone with a spudger.
- The slider is extremely delicate, so it is important you do not attempt to remove it from the sides.
- Gently pull the motherboard from the left side and remove it from the phone.
Disconnect the slider from the top of the phone with a spudger.
The slider is extremely delicate, so it is important you do not attempt to remove it from the sides.
Gently pull the motherboard from the left side and remove it from the phone.
Step 13
Rear Camera
- Using a spudger, disconnect the two metal rear camera tabs on the left side of the camera.
- Remove the camera from its slot on the motherboard.
Using a spudger, disconnect the two metal rear camera tabs on the left side of the camera.
Remove the camera from its slot on the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 5 other contributors
Rylee Cronin
Member since: 10/15/2019
220 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
Grand Valley State University, Team S4-G6, DeVasto Fall 2019
Member of Grand Valley State University, Team S4-G6, DeVasto Fall 2019
GVSU-DEVASTO-F19S4G6
4 Members
19 Guides authored
W W - Jul 28, 2020
Reply
In step 6 the screw under the humidity sensor is not shown. this needs to be removed as well
