Difficulty
Moderate
Steps
8
Time Required
15 - 30 minutes
Sections
3
- Clip Slip
- 1 step
- Backplate
- 4 steps
- LCD Screen
- 3 steps
Flags
2
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Better Introduction
Improve this guide by completing or revising its introduction.
BackOlympus Tough TG-1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Clip Side Repair
- Remove both 6 mm screws from the clip side of the camera.
- After you have removed the two screws, remove both the clip and the plate behind the clip so that the inside of the camera is exposed.
- If one of more of the clips appear to be broken, the back plate might need to be replaced.
Remove both 6 mm screws from the clip side of the camera.
After you have removed the two screws, remove both the clip and the plate behind the clip so that the inside of the camera is exposed.
If one of more of the clips appear to be broken, the back plate might need to be replaced.
1024
Step 2
Top of Camera
- The top of the camera does not contain screws. You do not need to remove anything from the top of the camera.
The top of the camera does not contain screws. You do not need to remove anything from the top of the camera.
Step 3
Plug Side
- Remove the two 5 mm screws on the side of the camera with the plug.
- Open the compartment door and remove both 6 cm screws inside of the compartment door. This will allow you to remove the tan piece held by the screws.
Remove the two 5 mm screws on the side of the camera with the plug.
Open the compartment door and remove both 6 cm screws inside of the compartment door. This will allow you to remove the tan piece held by the screws.
Step 4
Bottom
- Turn the camera so that you are looking at the bottom of the camera.
- Remove the two 4 mm screws from the bottom of the camera.
- The screws are different. The rear screw is has an unthreaded shank to locate the outer shell while screwing into the inner frame.
Turn the camera so that you are looking at the bottom of the camera.
Remove the two 4 mm screws from the bottom of the camera.
The screws are different. The rear screw is has an unthreaded shank to locate the outer shell while screwing into the inner frame.
Step 5
Front Panel
- Use the plastic opening tool to remove both components of the front panel. This includes the black part on the outside of the front panel and the main silver panel.
- Once every screw and panel is removed, you can replace the backplate to make your camera weatherproof again.
Use the plastic opening tool to remove both components of the front panel. This includes the black part on the outside of the front panel and the main silver panel.
Once every screw and panel is removed, you can replace the backplate to make your camera weatherproof again.
Step 6
Opening the Internal Case
- Using the plastic opening tools, carefully open the case.
- Do not tear the white circuit ribbon.
Using the plastic opening tools, carefully open the case.
Do not tear the white circuit ribbon.
Step 7
Opening the Screen's Protective Cover
- Using the screwdriver, remove the ten 3mm anchor screws.
- Using the plastic opening tool, open the protective cover so that the screen is exposed.
Using the screwdriver, remove the ten 3mm anchor screws.
Using the plastic opening tool, open the protective cover so that the screen is exposed.
Step 8
Unclipping the Screen from the Circuit Ribbon
- Carefully unclip the screen from its circuit ribbon.
Carefully unclip the screen from its circuit ribbon.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Emily Gensch
Member since: 01/21/2015
116 Reputation
1 Guide authored
Badges:
4
+1 more badge
Team
USF Tampa, Team 4-6, Brown Winter 2015
Member of USF Tampa, Team 4-6, Brown Winter 2015
USFT-BROWN-W15S4G6
4 Members
12 Guides authored
