Olympus Tough Tg 1 Circuit Board For Back Buttons Replacement Repair Guide

Difficulty

Difficult

Steps

10

Time Required

                          45 minutes - 2 hours            

Sections

4

• Clip Slip
• 1 step
• Backplate
• 4 steps
• LCD Screen
• 3 steps
• Circuit Board For Back Buttons
• 2 steps

Flags

2

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Better Introduction

Improve this guide by completing or revising its introduction.

• BackOlympus Tough TG-1

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

What you need

Step 1

              Clip Side Repair               

• Remove both 6 mm screws from the clip side of the camera.
• After you have removed the two screws, remove both the clip and the plate behind the clip so that the inside of the camera is exposed.
• If one of more of the clips appear to be broken, the back plate might need to be replaced.

Remove both 6 mm screws from the clip side of the camera.

After you have removed the two screws, remove both the clip and the plate behind the clip so that the inside of the camera is exposed.

If one of more of the clips appear to be broken, the back plate might need to be replaced.

1024

Step 2

              Top of Camera               

• The top of the camera does not contain screws. You do not need to remove anything from the top of the camera.

The top of the camera does not contain screws. You do not need to remove anything from the top of the camera.

Step 3

              Plug Side               

• Remove the two 5 mm screws on the side of the camera with the plug.
• Open the compartment door and remove both 6 cm screws inside of the compartment door. This will allow you to remove the tan piece held by the screws.

Remove the two 5 mm screws on the side of the camera with the plug.

Open the compartment door and remove both 6 cm screws inside of the compartment door. This will allow you to remove the tan piece held by the screws.

Step 4

              Bottom               

• Turn the camera so that you are looking at the bottom of the camera.
• Remove the two 4 mm screws from the bottom of the camera.
• The screws are different. The rear screw is has an unthreaded shank to locate the outer shell while screwing into the inner frame.

Turn the camera so that you are looking at the bottom of the camera.

Remove the two 4 mm screws from the bottom of the camera.

The screws are different. The rear screw is has an unthreaded shank to locate the outer shell while screwing into the inner frame.

Step 5

              Front Panel               

• Use the plastic opening tool to remove both components of the front panel. This includes the black part on the outside of the front panel and the main silver panel.
• Once every screw and panel is removed, you can replace the backplate to make your camera weatherproof again.

Use the plastic opening tool to remove both components of the front panel. This includes the black part on the outside of the front panel and the main silver panel.

Once every screw and panel is removed, you can replace the backplate to make your camera weatherproof again.

Step 6

              Opening the Internal Case               

• Using the plastic opening tools, carefully open the case.
• Do not tear the white circuit ribbon.

Using the plastic opening tools, carefully open the case.

Do not tear the white circuit ribbon.

Step 7

              Opening the Screen's Protective Cover               

• Using the screwdriver, remove the ten 3mm anchor screws.
• Using the plastic opening tool, open the protective cover so that the screen is exposed.

Using the screwdriver, remove the ten 3mm anchor screws.

Using the plastic opening tool, open the protective cover so that the screen is exposed.

Step 8

              Unclipping the Screen from the Circuit Ribbon               

• Carefully unclip the screen from its circuit ribbon.

Carefully unclip the screen from its circuit ribbon.

Step 9

              Circuit Board For Back Buttons               

• After removing this plastic casing from the screen, the only thing holding the circuit board to the plate is a screw 3 mm in length, with a diameter of 2.5 mm. Remove this screw.

After removing this plastic casing from the screen, the only thing holding the circuit board to the plate is a screw 3 mm in length, with a diameter of 2.5 mm. Remove this screw.

Step 10

• This is what your device should look like after removing the one screw.

This is what your device should look like after removing the one screw.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 2 other contributors 

                    Andrew Feliciano                     

Member since: 01/21/2015

122 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge                           

Team

                       USF Tampa, Team 4-6, Brown Winter 2015                        

                                                  Member of USF Tampa, Team 4-6, Brown Winter 2015 



                    USFT-BROWN-W15S4G6                     


                                            4 Members                     


                                            12 Guides authored