Difficulty

Difficult

Steps

12

Time Required

Suggest a time??

Sections

3

  • Battery
  • 3 steps
  • Back Case
  • 8 steps
  • Top Buttons
  • 1 step

Flags

0

  • BackOlympus TG-820 iHS

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Orient camera to look directly at battery compartment side as shown.

Orient camera to look directly at battery compartment side as shown.

1024

Step 2

  • Locate the two latches on the battery compartment.
  • First, move the “lock” switch left to reveal red indicator.
  • Next, move the “cover latch” switch downward to reveal red indicator.
  • You have to move the switches in that order for the compartment to unlatch.

Locate the two latches on the battery compartment.

First, move the “lock” switch left to reveal red indicator.

Next, move the “cover latch” switch downward to reveal red indicator.

You have to move the switches in that order for the compartment to unlatch.

Step 3

  • Allow the battery compartment latch to completely open.
  • Insert battery with the writing face up.
  • The bigger slot is for the battery. The smaller slot is for the memory card.
  • Battery not shown.

Allow the battery compartment latch to completely open.

Insert battery with the writing face up.

The bigger slot is for the battery. The smaller slot is for the memory card.

Battery not shown.

Step 4

              Back Case
  • Orient the camera so you are looking at the bottom.
  • Remove the three 3.85mm Phillips #00 screws from the bottom of the camera.

Orient the camera so you are looking at the bottom.

Remove the three 3.85mm Phillips #00 screws from the bottom of the camera.

Step 5

  • Orient the camera so you are looking at the side plate.
  • Remove the two 3.15mm Phillips #00 screws from the side plate of the camera.

Orient the camera so you are looking at the side plate.

Remove the two 3.15mm Phillips #00 screws from the side plate of the camera.

Step 6

  • Orient the camera so you are looking at the front plate.
  • Remove the two 3.8mm with the Phillips H1.5 from the front plate.
  • Remove the “Olympus” plate.

Orient the camera so you are looking at the front plate.

Remove the two 3.8mm with the Phillips H1.5 from the front plate.

Remove the “Olympus” plate.

Step 7

  • Remove face plate.

Remove face plate.

Step 8

  • Locate three small black screws inside of the battery compartment.
  • Remove the 3.85mm Phillips #00 screw on the far left side.
  • Remove the two 5mm Phillips #00 screws on the right side

Locate three small black screws inside of the battery compartment.

Remove the 3.85mm Phillips #00 screw on the far left side.

Remove the two 5mm Phillips #00 screws on the right side

Step 9

  • Orient the camera to be look at the top.
  • Remove the 5.4mm Phillips #00 screw on the top left side.
  • Remove the 7.4mm Phillips #00 screw next to the “ON/OFF” label.
  • Pry off top button plate with black nylon spudger.

Orient the camera to be look at the top.

Remove the 5.4mm Phillips #00 screw on the top left side.

Remove the 7.4mm Phillips #00 screw next to the “ON/OFF” label.

Pry off top button plate with black nylon spudger.

Step 10

  • Rotate to bottom of camera and locate bottom latch.
  • Wedge black nylon spudger in between bottom latch and camera base to release LCD Screen from camera.
  • Push firmly apart.
  • Some buttons might fall out.

Rotate to bottom of camera and locate bottom latch.

Wedge black nylon spudger in between bottom latch and camera base to release LCD Screen from camera.

Push firmly apart.

Some buttons might fall out.

Step 11

  • Orient the camera to the LCD screen side that is now wedged open.
  • Locate the white ribbon cable and pull out from motherboard.
  • Locate the brown ribbon cable and pull out from motherboard.

Orient the camera to the LCD screen side that is now wedged open.

Locate the white ribbon cable and pull out from motherboard.

Locate the brown ribbon cable and pull out from motherboard.

Step 12

              Top Buttons
  • Remove the two 3mm Phillips #00 screws.
  • Remove the one small black 2mm Phillips #00 screw.
  • Remove silver button plate from camera base.
  • Buttons may come loose

Remove the two 3mm Phillips #00 screws.

Remove the one small black 2mm Phillips #00 screw.

Remove silver button plate from camera base.

Buttons may come loose

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Larissa Knight

Member since: 03/21/2016

549 Reputation

                                      5 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Clemson, Team 7-2, Benson Spring 2016                        

                                                  Member of Clemson, Team 7-2, Benson Spring 2016 



                    CLEM-BENSON-S16S7G2                     


                                            4 Members                     


                                            16 Guides authored