Olympus Tg 820 Ihs Speaker Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Battery
3 steps
Back Case
8 steps
Speaker
2 steps

Flags

BackOlympus TG-820 iHS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Orient camera to look directly at battery compartment side as shown.

Orient camera to look directly at battery compartment side as shown.

1024

Step 2

Locate the two latches on the battery compartment.
First, move the “lock” switch left to reveal red indicator.
Next, move the “cover latch” switch downward to reveal red indicator.
You have to move the switches in that order for the compartment to unlatch.

Locate the two latches on the battery compartment.

First, move the “lock” switch left to reveal red indicator.

Next, move the “cover latch” switch downward to reveal red indicator.

You have to move the switches in that order for the compartment to unlatch.

Step 3

Allow the battery compartment latch to completely open.
Insert battery with the writing face up.
The bigger slot is for the battery. The smaller slot is for the memory card.
Battery not shown.

Allow the battery compartment latch to completely open.

Insert battery with the writing face up.

The bigger slot is for the battery. The smaller slot is for the memory card.

Battery not shown.

Step 4

              Back Case

Orient the camera so you are looking at the bottom.
Remove the three 3.85mm Phillips #00 screws from the bottom of the camera.

Orient the camera so you are looking at the bottom.

Remove the three 3.85mm Phillips #00 screws from the bottom of the camera.

Step 5

Orient the camera so you are looking at the side plate.
Remove the two 3.15mm Phillips #00 screws from the side plate of the camera.

Orient the camera so you are looking at the side plate.

Remove the two 3.15mm Phillips #00 screws from the side plate of the camera.

Step 6

Orient the camera so you are looking at the front plate.
Remove the two 3.8mm with the Phillips H1.5 from the front plate.
Remove the “Olympus” plate.

Orient the camera so you are looking at the front plate.

Remove the two 3.8mm with the Phillips H1.5 from the front plate.

Remove the “Olympus” plate.

Step 7

Remove face plate.

Remove face plate.

Step 8

Locate three small black screws inside of the battery compartment.
Remove the 3.85mm Phillips #00 screw on the far left side.
Remove the two 5mm Phillips #00 screws on the right side

Locate three small black screws inside of the battery compartment.

Remove the 3.85mm Phillips #00 screw on the far left side.

Remove the two 5mm Phillips #00 screws on the right side

Step 9

Orient the camera to be look at the top.
Remove the 5.4mm Phillips #00 screw on the top left side.
Remove the 7.4mm Phillips #00 screw next to the “ON/OFF” label.
Pry off top button plate with black nylon spudger.

Orient the camera to be look at the top.

Remove the 5.4mm Phillips #00 screw on the top left side.

Remove the 7.4mm Phillips #00 screw next to the “ON/OFF” label.

Pry off top button plate with black nylon spudger.

Step 10

Rotate to bottom of camera and locate bottom latch.
Wedge black nylon spudger in between bottom latch and camera base to release LCD Screen from camera.
Push firmly apart.
Some buttons might fall out.

Rotate to bottom of camera and locate bottom latch.

Wedge black nylon spudger in between bottom latch and camera base to release LCD Screen from camera.

Push firmly apart.

Some buttons might fall out.

Step 11

Orient the camera to the LCD screen side that is now wedged open.
Locate the white ribbon cable and pull out from motherboard.
Locate the brown ribbon cable and pull out from motherboard.

Orient the camera to the LCD screen side that is now wedged open.

Locate the white ribbon cable and pull out from motherboard.

Locate the brown ribbon cable and pull out from motherboard.

Step 12

              Speaker

Locate the speaker on the bottom right side of the camera
Use the spudger to lift the speaker out of the camera.

Locate the speaker on the bottom right side of the camera

Use the spudger to lift the speaker out of the camera.

Step 13

Next locate the solder points which connect the speaker to the motherboard, using the soldering kit(not pictured) the connection points can be removed, and the speaker can then be removed completely from the camera.
Learn how to solder here.

Next locate the solder points which connect the speaker to the motherboard, using the soldering kit(not pictured) the connection points can be removed, and the speaker can then be removed completely from the camera.

Learn how to solder here.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Larissa Knight

Member since: 03/21/2016

549 Reputation

                                      5 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Clemson, Team 7-2, Benson Spring 2016                        

                                                  Member of Clemson, Team 7-2, Benson Spring 2016 



                    CLEM-BENSON-S16S7G2                     


                                            4 Members                     


                                            16 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team