Difficulty
Difficult
Steps
14
Time Required
Suggest a time??
Sections
3
- Battery
- 3 steps
- Back Case
- 8 steps
- Lens
- 3 steps
Flags
0
BackOlympus TG-820 iHS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Orient camera to look directly at battery compartment side as shown.
Orient camera to look directly at battery compartment side as shown.
1024
Step 2
- Locate the two latches on the battery compartment.
- First, move the “lock” switch left to reveal red indicator.
- Next, move the “cover latch” switch downward to reveal red indicator.
- You have to move the switches in that order for the compartment to unlatch.
Locate the two latches on the battery compartment.
First, move the “lock” switch left to reveal red indicator.
Next, move the “cover latch” switch downward to reveal red indicator.
You have to move the switches in that order for the compartment to unlatch.
Step 3
- Allow the battery compartment latch to completely open.
- Insert battery with the writing face up.
- The bigger slot is for the battery. The smaller slot is for the memory card.
- Battery not shown.
Allow the battery compartment latch to completely open.
Insert battery with the writing face up.
The bigger slot is for the battery. The smaller slot is for the memory card.
Battery not shown.
Step 4
Back Case
- Orient the camera so you are looking at the bottom.
- Remove the three 3.85mm Phillips #00 screws from the bottom of the camera.
Orient the camera so you are looking at the bottom.
Remove the three 3.85mm Phillips #00 screws from the bottom of the camera.
Step 5
- Orient the camera so you are looking at the side plate.
- Remove the two 3.15mm Phillips #00 screws from the side plate of the camera.
Orient the camera so you are looking at the side plate.
Remove the two 3.15mm Phillips #00 screws from the side plate of the camera.
Step 6
- Orient the camera so you are looking at the front plate.
- Remove the two 3.8mm with the Phillips H1.5 from the front plate.
- Remove the “Olympus” plate.
Orient the camera so you are looking at the front plate.
Remove the two 3.8mm with the Phillips H1.5 from the front plate.
Remove the “Olympus” plate.
Step 7
- Remove face plate.
Remove face plate.
Step 8
- Locate three small black screws inside of the battery compartment.
- Remove the 3.85mm Phillips #00 screw on the far left side.
- Remove the two 5mm Phillips #00 screws on the right side
Locate three small black screws inside of the battery compartment.
Remove the 3.85mm Phillips #00 screw on the far left side.
Remove the two 5mm Phillips #00 screws on the right side
Step 9
- Orient the camera to be look at the top.
- Remove the 5.4mm Phillips #00 screw on the top left side.
- Remove the 7.4mm Phillips #00 screw next to the “ON/OFF” label.
- Pry off top button plate with black nylon spudger.
Orient the camera to be look at the top.
Remove the 5.4mm Phillips #00 screw on the top left side.
Remove the 7.4mm Phillips #00 screw next to the “ON/OFF” label.
Pry off top button plate with black nylon spudger.
Step 10
- Rotate to bottom of camera and locate bottom latch.
- Wedge black nylon spudger in between bottom latch and camera base to release LCD Screen from camera.
- Push firmly apart.
- Some buttons might fall out.
Rotate to bottom of camera and locate bottom latch.
Wedge black nylon spudger in between bottom latch and camera base to release LCD Screen from camera.
Push firmly apart.
Some buttons might fall out.
Step 11
- Orient the camera to the LCD screen side that is now wedged open.
- Locate the white ribbon cable and pull out from motherboard.
- Locate the brown ribbon cable and pull out from motherboard.
Orient the camera to the LCD screen side that is now wedged open.
Locate the white ribbon cable and pull out from motherboard.
Locate the brown ribbon cable and pull out from motherboard.
Step 12
Lens
- Remove the four silver and one black screws using the Phillips #000 screwdriver from the metal holding plate and lift the plate out of the camera
- Locate and remove the two screws on the left side of the camera using the Phillips #000, then remove the metal plates they rest on.
Remove the four silver and one black screws using the Phillips #000 screwdriver from the metal holding plate and lift the plate out of the camera
Locate and remove the two screws on the left side of the camera using the Phillips #000, then remove the metal plates they rest on.
Step 13
- Using the plastic opening tool, pry the black component out of the cameras casing.
- The black component is connected to the motherboard using some ribbon cables, it is not necessary to disconnect these cables to replace the lens.
- The black component will just fold out for access to the lens mechanism
Using the plastic opening tool, pry the black component out of the cameras casing.
The black component is connected to the motherboard using some ribbon cables, it is not necessary to disconnect these cables to replace the lens.
The black component will just fold out for access to the lens mechanism
Step 14
- Locate the three silver screws on the top of the lens, and remove them using the Phillips #000 screwdriver
- Locate the two screws on the right side of the lens, and remove them with the Phillips #000 screwdriver.
- After removing the screws, the lens will just lift free from the black component.
Locate the three silver screws on the top of the lens, and remove them using the Phillips #000 screwdriver
Locate the two screws on the right side of the lens, and remove them with the Phillips #000 screwdriver.
After removing the screws, the lens will just lift free from the black component.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Leslie Cade
Member since: 03/21/2016
343 Reputation
3 Guides authored
Badges:
9
+6 more badges
Team
Clemson, Team 7-2, Benson Spring 2016
Member of Clemson, Team 7-2, Benson Spring 2016
CLEM-BENSON-S16S7G2
4 Members
16 Guides authored