Difficulty
Moderate
Steps
14
Time Required
30 minutes
Sections
3
- Back Case
- 6 steps
- LCD Screen
- 3 steps
- Lens
- 5 steps
Flags
1
Needs More Images
A few more images would make this guide’s procedures crystal clear.
BackOlympus SZ-12
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Case
- Remove nine 4.45mm Phillips #000 screws from the outside of the case.
Remove nine 4.45mm Phillips #000 screws from the outside of the case.
1024
Step 2
- There are four screws to take out on the bottom of the camera.
There are four screws to take out on the bottom of the camera.
Step 3
- There are three screws to take out on this side.
There are three screws to take out on this side.
Step 4
- There is one screw to take out on this side.
There is one screw to take out on this side.
Step 5
- There is one hidden screw inside the HDMI port.
There is one hidden screw inside the HDMI port.
Step 6
- Using the blue plastic opening tool, wedge open and remove the case.
Using the blue plastic opening tool, wedge open and remove the case.
Step 7
LCD Screen
- Once you have the back case off, remove the LCD Screen.
Once you have the back case off, remove the LCD Screen.
Step 8
- Using a plastic opening tool, gently lift the retaining flap on the display cable ZIF connector.
- Pull the display cable from its socket on the motherboard.
Using a plastic opening tool, gently lift the retaining flap on the display cable ZIF connector.
Pull the display cable from its socket on the motherboard.
Step 9
- Remove the LCD screen from the device.
- Be careful not to rip the display’s ribbon cable as you pull the screen away from the device.
Remove the LCD screen from the device.
Be careful not to rip the display’s ribbon cable as you pull the screen away from the device.
Step 10
Lens
- Remove the four 3.8mm Phillips #000 screws from the LCD frame.
Remove the four 3.8mm Phillips #000 screws from the LCD frame.
Step 11
- Remove the top left screw, top right screw, bottom left screw, and bottom right screw from LCD frame.
Remove the top left screw, top right screw, bottom left screw, and bottom right screw from LCD frame.
Step 12
- Lift the retaining flaps on the three remaining ZIF connectors connected to the motherboard.
Lift the retaining flaps on the three remaining ZIF connectors connected to the motherboard.
Step 13
- Remove the five 4.3mm Phillips #000 screws from the lens frame to access the lens.
- Remove the lens frame.
Remove the five 4.3mm Phillips #000 screws from the lens frame to access the lens.
Remove the lens frame.
Step 14
- Remove two 4.3mm Phillips #000 screws from black plastic piece surrounding the lens.
- Remove the lens.
Remove two 4.3mm Phillips #000 screws from black plastic piece surrounding the lens.
Remove the lens.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Samuel Hays
Member since: 03/13/2017
515 Reputation
4 Guides authored
Badges:
9
+6 more badges
Team
Carson-Newman University, Team S1-G1, Sobiech Spring 2017
Member of Carson-Newman University, Team S1-G1, Sobiech Spring 2017
CNU-SOBIECH-S17S1G1
4 Members
8 Guides authored
Deacon - Aug 3, 2021
Reply
Is her anything in the lens assembly that I could look for which may have dislodged showing up as a shadow on the bottom of the display screen