Olympus Stylus Tough Tg 2 Ihs Back Panel Buttons Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          3 - 5 minutes

Sections

Connector Port Casing
3 steps
Strap Eyelet Casing
2 steps
Front Case
3 steps
Display Assembly
5 steps
Back Panel & Buttons
2 steps

Flags

BackOlympus Stylus Tough TG-2 iHS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Connector Port Casing

Locate the side of the camera with the connector cover.
Remove the 2 Phillips #00 4.6mm casing screws.

Locate the side of the camera with the connector cover.

Remove the 2 Phillips #00 4.6mm casing screws.

1024

Step 2

Open the connector cover by sliding the tab labeled lock to revile orange.
Slide the connector cover lock to revile orange and the door will spring open.
Remove the single internal Phillips #00 3.77mm screw.

Open the connector cover by sliding the tab labeled lock to revile orange.

Slide the connector cover lock to revile orange and the door will spring open.

Remove the single internal Phillips #00 3.77mm screw.

Step 3

Close the door to gain access to the casing.
Use your fingers to remove the black plastic casing that surrounds the connector door.
Use your fingers to remove the next black plastic piece .
Remove the two screws revealed

Close the door to gain access to the casing.

Use your fingers to remove the black plastic casing that surrounds the connector door.

Use your fingers to remove the next black plastic piece .

Remove the two screws revealed

Step 4

              Strap Eyelet Casing

Locate the strap eyelet side of the camera and remove the 2 Phillips #00 5.3mm screws in the handle.
Using your fingers, take off the handle, the black casing underneath, and gently wiggle out the shiny black casing below that.

Locate the strap eyelet side of the camera and remove the 2 Phillips #00 5.3mm screws in the handle.

Using your fingers, take off the handle, the black casing underneath, and gently wiggle out the shiny black casing below that.

Step 5

On the bottom of the camera, remove the single Phillips #00 3.5mm screw from the casing below the grip.
Using a plastic opening tool, gently pry the Olympus grip up and remove it.

On the bottom of the camera, remove the single Phillips #00 3.5mm screw from the casing below the grip.

Using a plastic opening tool, gently pry the Olympus grip up and remove it.

Step 6

              Front Case

Remove the red ring surrounding the lens by twisting it counter-clockwise

Remove the red ring surrounding the lens by twisting it counter-clockwise

Step 7

Remove the 2 Phillips #00 3.4mm screws that secure the faceplate just reveled by the grip.
On the bottom of the camera, remove the single Phillips #00 3.4mm screw by the tripod socket securing the face plate.

Remove the 2 Phillips #00 3.4mm screws that secure the faceplate just reveled by the grip.

On the bottom of the camera, remove the single Phillips #00 3.4mm screw by the tripod socket securing the face plate.

Step 8

Use a plastic prying tool to lift and remove the faceplate .
There will be some resistance from a sticker just under the GPS logo.
The black plastic ring around the flash may fall as it is no longer secure.

Use a plastic prying tool to lift and remove the faceplate .

There will be some resistance from a sticker just under the GPS logo.

The black plastic ring around the flash may fall as it is no longer secure.

Step 9

              Display Assembly

To detach the monitor screen, remove the following 7 screws:
Locate the flash and remove the 2 Phillips #00 9.23mm & 14.87mm screws.
Locate the battery door and remove the single Phillips #00 3.37mm screw.
On the bottom of the camera, remove the single Phillips 3.58mm screw near the tripod socket.

To detach the monitor screen, remove the following 7 screws:

Locate the flash and remove the 2 Phillips #00 9.23mm & 14.87mm screws.

Locate the battery door and remove the single Phillips #00 3.37mm screw.

On the bottom of the camera, remove the single Phillips 3.58mm screw near the tripod socket.

Step 10

On the face plate, locate and remove the 2 eyelet strap side Phillips #00 9.2mm corner screws and the lower battery corner Phillips #00 14.87mm screw.
Use your fingers to unclasp the casing clips on either side of the camera and pull down the monitor casing.
Using the spudger to gently pry the screen away from the body of the camera.

On the face plate, locate and remove the 2 eyelet strap side Phillips #00 9.2mm corner screws and the lower battery corner Phillips #00 14.87mm screw.

Use your fingers to unclasp the casing clips on either side of the camera and pull down the monitor casing.

Using the spudger to gently pry the screen away from the body of the camera.

Step 11

Locate the clasp for the white ribbon.
Use the spudger to lift the clasp releasing the ribbon

Locate the clasp for the white ribbon.

Use the spudger to lift the clasp releasing the ribbon

Step 12

Locate the clasp for the orange ribbon in between the motherboard and lens box.
Use the spudger to lift the clasp releasing the ribbon.

Locate the clasp for the orange ribbon in between the motherboard and lens box.

Use the spudger to lift the clasp releasing the ribbon.

Step 13

Next pry up on the white connector using the spudger to free the screen from the device.
The housing and monitor will be separated.

Next pry up on the white connector using the spudger to free the screen from the device.

The housing and monitor will be separated.

Step 14

              Back Panel & Buttons

On the back of the separated monitor, remove the 10 silver Phillips #00 4.4mm screws and the 1 black Phillips #00 3.26mm screw.
Use your fingers to remove the small corner metal triangle.
Using the spudger on the edge of the screen to lift it and remove the metal insert.

On the back of the separated monitor, remove the 10 silver Phillips #00 4.4mm screws and the 1 black Phillips #00 3.26mm screw.

Use your fingers to remove the small corner metal triangle.

Using the spudger on the edge of the screen to lift it and remove the metal insert.

Step 15

Use your fingers to lift the green circuit board and buttons out of the case.

Use your fingers to lift the green circuit board and buttons out of the case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 3 other contributors

                    Amanda

Member since: 07/20/2015

918 Reputation

                                      8 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Eastern Washington University, Team 1-5, Carnegie Fall 2015                        

                                                  Member of Eastern Washington University, Team 1-5, Carnegie Fall 2015 



                    EWU-CARNEGIE-F15S1G5                     


                                            3 Members                     


                                            16 Guides authored

epaulan - Oct 10, 2015

Any advice on where to buy a replacement back panel for the TG-2?

Introduction#

What you need#

Team#

Introduction

What you need

Team