Difficulty
Moderate
Steps
11
Time Required
Suggest a time??
Sections
2
- Prerequisite Guide
- 9 steps
- LCD
- 2 steps
Flags
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackOlympus Stylus Tough 6020
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Slide and push the battery casing to open it.
- Push the battery to eject it.
Slide and push the battery casing to open it.
Push the battery to eject it.
1024
Step 2
Bottom Plating
- Turn the camera so that you are facing the bottom of the camera.
- Using a Phillips 00 screwdriver, unscrew the three 3.9mm screws on the bottom of the camera.
- Using a spudger, pry off the plating on the bottom of the camera.
Turn the camera so that you are facing the bottom of the camera.
Using a Phillips 00 screwdriver, unscrew the three 3.9mm screws on the bottom of the camera.
Using a spudger, pry off the plating on the bottom of the camera.
Step 3
Top Plating
- Turn the camera so that you are facing the top of the camera.
- Using a Phillips 00 screwdriver, unscrew the three 3.9mm screws located on the top of the camera.
- Using a spudger, pry off the plating on the top of the camera.
Turn the camera so that you are facing the top of the camera.
Using a Phillips 00 screwdriver, unscrew the three 3.9mm screws located on the top of the camera.
Using a spudger, pry off the plating on the top of the camera.
Step 4
Left Plating
- Turn the camera so the LCD is facing upwards.
- Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws located on the left side of the device.
Turn the camera so the LCD is facing upwards.
Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws located on the left side of the device.
Step 5
Black "Olympus" Face Plate
- Using a Phillips 00 screwdriver, unscrew the 3.9mm screw located next to the black “Olympus” face plate.
- Using a T6 Torx screwdriver, unscrew the two 3.5mm screws located on the black “Olympus” face plate.
- Using a spudger, gently pry off the black “Olympus” face plate.
Using a Phillips 00 screwdriver, unscrew the 3.9mm screw located next to the black “Olympus” face plate.
Using a T6 Torx screwdriver, unscrew the two 3.5mm screws located on the black “Olympus” face plate.
Using a spudger, gently pry off the black “Olympus” face plate.
Step 6
End Casing
- Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws to the right of the cursor pad on the U-shaped frame.
- Turn the device over so the front of the camera is facing you.
- Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws on the end casing.
- Using a spudger, pry off the end casing.
Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws to the right of the cursor pad on the U-shaped frame.
Turn the device over so the front of the camera is facing you.
Using a Phillips 00 screwdriver, unscrew the two 3.9mm screws on the end casing.
Using a spudger, pry off the end casing.
Step 7
Blue Face Plate
- Turn the camera so the blue face plate is visible.
- Using a Phillips 00 screwdriver, unscrew the two 3mm screws on the blue plate.
- Using a Phillips 00 screwdriver, unscrew the 3.9mm screw located at the bottom of the camera straight down from the flash.
- Using a spudger, gently pry off the blue face plate.
Turn the camera so the blue face plate is visible.
Using a Phillips 00 screwdriver, unscrew the two 3mm screws on the blue plate.
Using a Phillips 00 screwdriver, unscrew the 3.9mm screw located at the bottom of the camera straight down from the flash.
Using a spudger, gently pry off the blue face plate.
Step 8
Back Plate
- Using a Phillips 00 screwdriver, unscrew the 9mm screws on the top of the camera to the right of the flash.
Using a Phillips 00 screwdriver, unscrew the 9mm screws on the top of the camera to the right of the flash.
Step 9
- Using a Phillips 00 screwdriver, unscrew the wide 3.5mm screw located in the middle of the camera.
- Using a Phillips 00 screwdriver, unscrew the 9mm screw located at the top left corner of the camera.
- Using a spudger, separate the black plate from the camera.
Using a Phillips 00 screwdriver, unscrew the wide 3.5mm screw located in the middle of the camera.
Using a Phillips 00 screwdriver, unscrew the 9mm screw located at the top left corner of the camera.
Using a spudger, separate the black plate from the camera.
Step 10
Ribbon Cables
- Using tweezers, pull the white ribbon cable to disconnect it.
- Using tweezers, pull the brown ribbon cable to disconnect it.
Using tweezers, pull the white ribbon cable to disconnect it.
Using tweezers, pull the brown ribbon cable to disconnect it.
Step 11
LCD Screen
- Using the Phillips #00 Screwdriver, unscrew the 3.9mm screws on the back left side of the LCD screen case.
- Using the spudger, gently pry the two screw holders from the LCD screen case.
- Using your hands, gently push LCD through the LCD screen case.
Using the Phillips #00 Screwdriver, unscrew the 3.9mm screws on the back left side of the LCD screen case.
Using the spudger, gently pry the two screw holders from the LCD screen case.
Using your hands, gently push LCD through the LCD screen case.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Luke Wiley
Member since: 04/08/2015
263 Reputation
2 Guides authored
Badges:
6
+3 more badges
Team
Eastern Washington University, Team 2-6, Matresse Spring 2015
Member of Eastern Washington University, Team 2-6, Matresse Spring 2015
EWU-MATRESSE-S15S2G6
4 Members
12 Guides authored
