Difficulty
Moderate
Steps
14
Time Required
30 - 45 minutes
Sections
3
- Slider
- 4 steps
- Outer Case
- 7 steps
- LCD Screen
- 3 steps
Flags
1
Confusing Text
Some of this guide’s text is confusing, duplicated, or off-topic. Clarify it by editing!
BackOlympus Stylus 410
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Slider
- Locate the 2 screws on the bottom of the slider.
- Remove both screws with a #00 Phillips screwdriver.
Locate the 2 screws on the bottom of the slider.
Remove both screws with a #00 Phillips screwdriver.
1024
Step 2
- Gently pull on the bottom of the slider until it comes off the lower track.
- There is a little piece that connects the slider to the track. Be sure not to lose this as it is needed to put the slider back on.
Gently pull on the bottom of the slider until it comes off the lower track.
There is a little piece that connects the slider to the track. Be sure not to lose this as it is needed to put the slider back on.
Step 3
- Lift the slider up until it comes off the upper track.
Lift the slider up until it comes off the upper track.
Step 4
- The slider should now be free from the body of the camera.
The slider should now be free from the body of the camera.
Step 5
Outer Case
- Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver.
Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver.
Step 6
- Use the spudger to peel off the outer metal band, starting from the bottom of the camera.
- The metal band it attached to the camera with glue in addition to screws. Be careful not to bend the band when removing it from the camera.
Use the spudger to peel off the outer metal band, starting from the bottom of the camera.
The metal band it attached to the camera with glue in addition to screws. Be careful not to bend the band when removing it from the camera.
Step 7
- The shutter button can now be removed. It is not connected to the camera and can be lifted off.
The shutter button can now be removed. It is not connected to the camera and can be lifted off.
Step 8
- Remove the memory card.
- Locate and remove the 2 screws using a #00 Phillips screwdriver.
Remove the memory card.
Locate and remove the 2 screws using a #00 Phillips screwdriver.
Step 9
- Use a spudger around the edge of the case to loosen it.
- Carefully wiggle the back case off. This may require a fair amount of force.
Use a spudger around the edge of the case to loosen it.
Carefully wiggle the back case off. This may require a fair amount of force.
Step 10
- Locate the 3 internal screws holding on the front of the case. Remove them with a #00 Phillips screwdriver.
Locate the 3 internal screws holding on the front of the case. Remove them with a #00 Phillips screwdriver.
Step 11
- While grasping the interior and the front case, gently pull until they start to come apart. Some light wiggling may be required.
- Be careful not to completely pull the front case off because it will still be connected with wires.
While grasping the interior and the front case, gently pull until they start to come apart. Some light wiggling may be required.
Be careful not to completely pull the front case off because it will still be connected with wires.
Step 12
LCD Screen
- Remove the metal frame from the LCD screen using a spudger.
Remove the metal frame from the LCD screen using a spudger.
Step 13
- Pry off the LCD screen from the top using a spudger. The screen will not be completely free from the device because of a ribbon.
- Do not pull the screen completely off because it will still be held on by two ribbon cables.
Pry off the LCD screen from the top using a spudger. The screen will not be completely free from the device because of a ribbon.
Do not pull the screen completely off because it will still be held on by two ribbon cables.
Step 14
- This is what the camera will look like now that the LCD screen is removed.
This is what the camera will look like now that the LCD screen is removed.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Rory Aronson
Member since: 04/15/2010
46 Reputation
6 Guides authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 6-13, Maness Spring 2010
Member of Cal Poly, Team 6-13, Maness Spring 2010
CPSU-MANESS-S10S6G13
5 Members
17 Guides authored
