Olympus Stylus 410 Flash Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 hour

Sections

Slider
4 steps
Outer Case
7 steps
Flash
2 steps

Flags

BackOlympus Stylus 410
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Slider

Locate the 2 screws on the bottom of the slider.
Remove both screws with a #00 Phillips screwdriver.

Locate the 2 screws on the bottom of the slider.

Remove both screws with a #00 Phillips screwdriver.

1024

Step 2

Gently pull on the bottom of the slider until it comes off the lower track.
There is a little piece that connects the slider to the track. Be sure not to lose this as it is needed to put the slider back on.

Gently pull on the bottom of the slider until it comes off the lower track.

There is a little piece that connects the slider to the track. Be sure not to lose this as it is needed to put the slider back on.

Step 3

Lift the slider up until it comes off the upper track.

Lift the slider up until it comes off the upper track.

Step 4

The slider should now be free from the body of the camera.

The slider should now be free from the body of the camera.

Step 5

              Outer Case

Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver.

Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver.

Step 6

Use the spudger to peel off the outer metal band, starting from the bottom of the camera.
The metal band it attached to the camera with glue in addition to screws. Be careful not to bend the band when removing it from the camera.

Use the spudger to peel off the outer metal band, starting from the bottom of the camera.

The metal band it attached to the camera with glue in addition to screws. Be careful not to bend the band when removing it from the camera.

Step 7

The shutter button can now be removed. It is not connected to the camera and can be lifted off.

The shutter button can now be removed. It is not connected to the camera and can be lifted off.

Step 8

Remove the memory card.
Locate and remove the 2 screws using a #00 Phillips screwdriver.

Remove the memory card.

Locate and remove the 2 screws using a #00 Phillips screwdriver.

Step 9

Use a spudger around the edge of the case to loosen it.
Carefully wiggle the back case off. This may require a fair amount of force.

Use a spudger around the edge of the case to loosen it.

Carefully wiggle the back case off. This may require a fair amount of force.

Step 10

Locate the 3 internal screws holding on the front of the case. Remove them with a #00 Phillips screwdriver.

Locate the 3 internal screws holding on the front of the case. Remove them with a #00 Phillips screwdriver.

Step 11

While grasping the interior and the front case, gently pull until they start to come apart. Some light wiggling may be required.
Be careful not to completely pull the front case off because it will still be connected with wires.

While grasping the interior and the front case, gently pull until they start to come apart. Some light wiggling may be required.

Be careful not to completely pull the front case off because it will still be connected with wires.

Step 12

              Flash

Locate the gray compartment covering the flash.
Position your flat head screw driver or small spudger underneath the tab that is keeping the gray cover on.
Gently lift the tab so the gray compartment becomes free.

Locate the gray compartment covering the flash.

Position your flat head screw driver or small spudger underneath the tab that is keeping the gray cover on.

Gently lift the tab so the gray compartment becomes free.

Step 13

Use the spudger around the perimeter of the gray compartment to detach it from the front case.
The gray compartment can now be removed from the flash unit.
The flash unit can now be removed, and a new one soldered back on.

Use the spudger around the perimeter of the gray compartment to detach it from the front case.

The gray compartment can now be removed from the flash unit.

The flash unit can now be removed, and a new one soldered back on.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Rory Aronson

Member since: 04/15/2010

46 Reputation

                                      6 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Cal Poly, Team 6-13, Maness Spring 2010                        

                                                  Member of Cal Poly, Team 6-13, Maness Spring 2010 



                    CPSU-MANESS-S10S6G13                     


                                            5 Members                     


                                            17 Guides authored

ken arnoldi - Sep 18, 2016

Good instructions, but author doesn’t say where or how to get new flash unit!

Ken Arnoldi

Good instructions but author doesn’t say how or where to get new flash unit!

Introduction#

What you need#

Team#

Introduction

What you need

Team