Difficulty

Moderate

Steps

14

Time Required

Suggest a time??

Sections

2

  • Olympus Stylus 1030 SW Camera Disassembly
  • 11 steps
  • LCD and Buttons
  • 3 steps

Flags

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackOlympus Stylus 1030 SW

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Olympus Stylus 1030 SW Camera Disassembly
  • Using the iFixit Opening Tool, pry off the plastic part of the lens.
  • Using the T6 Torx screwdriver, unscrew the three screws.

Using the iFixit Opening Tool, pry off the plastic part of the lens.

Using the T6 Torx screwdriver, unscrew the three screws.

1024

Step 2

  • Using the Phillips #00 screwdriver, unscrew the three screws.
  • Carefully swivel the metal cover out towards you.
  • Using tweezers, remove the metal washer.

Using the Phillips #00 screwdriver, unscrew the three screws.

Carefully swivel the metal cover out towards you.

Using tweezers, remove the metal washer.

Step 3

  • Using the tweezers, slowly peel off the plate.

Using the tweezers, slowly peel off the plate.

Step 4

  • Using the Phillips #00 screwdriver, unscrew the two screws on the side of the camera.

Using the Phillips #00 screwdriver, unscrew the two screws on the side of the camera.

Step 5

  • On the opposite side, use the Phillips #00 screwdriver to unscrew both screws.
  • Take out the speaker plate.
  • Open the multi-connector cover and slide off the side panel.

On the opposite side, use the Phillips #00 screwdriver to unscrew both screws.

Take out the speaker plate.

Open the multi-connector cover and slide off the side panel.

Step 6

  • Using the Phillips #00 screwdriver, unscrew the screw above the speaker.
  • On the bottom side of the camera, unscrew the two screws.

Using the Phillips #00 screwdriver, unscrew the screw above the speaker.

On the bottom side of the camera, unscrew the two screws.

Step 7

  • Open the battery compartment cover.
  • Use the Phillips #00 screwdriver to unscrew the screw in the battery compartment.

Open the battery compartment cover.

Use the Phillips #00 screwdriver to unscrew the screw in the battery compartment.

Step 8

  • On the front of the camera, unscrew the two screws shown.
  • Gently pull on the side until the camera is separated from the back panel.
  • Remove the shutter and power button.

On the front of the camera, unscrew the two screws shown.

Gently pull on the side until the camera is separated from the back panel.

Remove the shutter and power button.

Step 9

  • Use the Phillips #00 screwdriver to unscrew the four screws on the front of the camera.
  • Unscrew the shutter using the Phillips #00 screwdriver.

Use the Phillips #00 screwdriver to unscrew the four screws on the front of the camera.

Unscrew the shutter using the Phillips #00 screwdriver.

Step 10

  • Release the top holding using a spudger.
  • Slowly and carefully separate the front and back of the camera, exposing the electrical ribbons.

Release the top holding using a spudger.

Slowly and carefully separate the front and back of the camera, exposing the electrical ribbons.

Step 11

  • Using the spudger and tweezers if needed, remove the ribbons from the computer chips.

Using the spudger and tweezers if needed, remove the ribbons from the computer chips.

Step 12

              LCD and Buttons
  • Unscrew the two screws found on the left side of the screen using the PH#00 head.
  • Peel off the gel tape using tweezers.
  • Unscrew the five 0.6 mm screws using the PH#00 head.

Unscrew the two screws found on the left side of the screen using the PH#00 head.

Peel off the gel tape using tweezers.

Unscrew the five 0.6 mm screws using the PH#00 head.

Step 13

  • Use the spudger to carefully pry off the LCD screen.

Use the spudger to carefully pry off the LCD screen.

Step 14

  • Use the tweezers to take out the rubber button holder and its buttons.

Use the tweezers to take out the rubber button holder and its buttons.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 7 other contributors 


                    Shanmei Zheng

Member since: 02/17/2014

301 Reputation

                                      3 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       University of Illinois Urbana-Champaign, Team 1-2, Scrogum Spring 2014                        

                                                  Member of University of Illinois Urbana-Champaign, Team 1-2, Scrogum Spring 2014 



                    UICU-SCROGUM-S14S1G2                     


                                            5 Members                     


                                            10 Guides authored