Difficulty
Moderate
Steps
14
Time Required
35 - 40 minutes
Sections
2
- Olympus Stylus 1030 SW Camera Disassembly
- 11 steps
- Camera Lens
- 3 steps
Flags
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Better Introduction
Improve this guide by completing or revising its introduction.
BackOlympus Stylus 1030 SW
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Olympus Stylus 1030 SW Camera Disassembly
- Using the iFixit Opening Tool, pry off the plastic part of the lens.
- Using the T6 Torx screwdriver, unscrew the three screws.
Using the iFixit Opening Tool, pry off the plastic part of the lens.
Using the T6 Torx screwdriver, unscrew the three screws.
1024
Step 2
- Using the Phillips #00 screwdriver, unscrew the three screws.
- Carefully swivel the metal cover out towards you.
- Using tweezers, remove the metal washer.
Using the Phillips #00 screwdriver, unscrew the three screws.
Carefully swivel the metal cover out towards you.
Using tweezers, remove the metal washer.
Step 3
- Using the tweezers, slowly peel off the plate.
Using the tweezers, slowly peel off the plate.
Step 4
- Using the Phillips #00 screwdriver, unscrew the two screws on the side of the camera.
Using the Phillips #00 screwdriver, unscrew the two screws on the side of the camera.
Step 5
- On the opposite side, use the Phillips #00 screwdriver to unscrew both screws.
- Take out the speaker plate.
- Open the multi-connector cover and slide off the side panel.
On the opposite side, use the Phillips #00 screwdriver to unscrew both screws.
Take out the speaker plate.
Open the multi-connector cover and slide off the side panel.
Step 6
- Using the Phillips #00 screwdriver, unscrew the screw above the speaker.
- On the bottom side of the camera, unscrew the two screws.
Using the Phillips #00 screwdriver, unscrew the screw above the speaker.
On the bottom side of the camera, unscrew the two screws.
Step 7
- Open the battery compartment cover.
- Use the Phillips #00 screwdriver to unscrew the screw in the battery compartment.
Open the battery compartment cover.
Use the Phillips #00 screwdriver to unscrew the screw in the battery compartment.
Step 8
- On the front of the camera, unscrew the two screws shown.
- Gently pull on the side until the camera is separated from the back panel.
- Remove the shutter and power button.
On the front of the camera, unscrew the two screws shown.
Gently pull on the side until the camera is separated from the back panel.
Remove the shutter and power button.
Step 9
- Use the Phillips #00 screwdriver to unscrew the four screws on the front of the camera.
- Unscrew the shutter using the Phillips #00 screwdriver.
Use the Phillips #00 screwdriver to unscrew the four screws on the front of the camera.
Unscrew the shutter using the Phillips #00 screwdriver.
Step 10
- Release the top holding using a spudger.
- Slowly and carefully separate the front and back of the camera, exposing the electrical ribbons.
Release the top holding using a spudger.
Slowly and carefully separate the front and back of the camera, exposing the electrical ribbons.
Step 11
- Using the spudger and tweezers if needed, remove the ribbons from the computer chips.
Using the spudger and tweezers if needed, remove the ribbons from the computer chips.
Step 12
Camera Lens
- Peel off the black tape using tweezers.
- Unscrew the 1.0 cm screw.
- Use the spudger to carefully take out the lens compartment.
Peel off the black tape using tweezers.
Unscrew the 1.0 cm screw.
Use the spudger to carefully take out the lens compartment.
Step 13
- Carefully take out the lens and the black plastic pieces along with it.
Carefully take out the lens and the black plastic pieces along with it.
Step 14
- Unscrew the three screws found on top of the mirror lens.
- The mirror lens can now be removed.
Unscrew the three screws found on top of the mirror lens.
The mirror lens can now be removed.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 6 other contributors
Shanmei Zheng
Member since: 02/17/2014
301 Reputation
3 Guides authored
Badges:
6
+3 more badges
Team
University of Illinois Urbana-Champaign, Team 1-2, Scrogum Spring 2014
Member of University of Illinois Urbana-Champaign, Team 1-2, Scrogum Spring 2014
UICU-SCROGUM-S14S1G2
5 Members
10 Guides authored