Difficulty
Moderate
Steps
14
Time Required
10 - 15 minutes
Sections
3
- Disassembling Olympus Stylus 1010 Case
- 7 steps
- Lens
- 3 steps
- Motherboard
- 4 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackOlympus Stylus 1010
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Disassembling Olympus Stylus 1010 Case
- Remove the five Phillips #00 bottom and right side panel screws.
Remove the five Phillips #00 bottom and right side panel screws.
1024
Step 2
- Remove the right side panel by pulling off the large silver piece.
Remove the right side panel by pulling off the large silver piece.
Step 3
- Remove the remaining three Phillips #00 side and front panel screws.
Remove the remaining three Phillips #00 side and front panel screws.
Step 4
- Using your thumb and forefinger, pull off the silver name plate and silver “T-shape” piece.
Using your thumb and forefinger, pull off the silver name plate and silver “T-shape” piece.
Step 5
- Remove the black front panel by sliding it towards the lens and then pulling it up off of the camera.
Remove the black front panel by sliding it towards the lens and then pulling it up off of the camera.
Step 6
- Remove the three Phillips #00 screws from the front of the camera.
- Using a spudger, lift the two tabs to separate the case—one tab on top and one tab on the right side.
Remove the three Phillips #00 screws from the front of the camera.
Using a spudger, lift the two tabs to separate the case—one tab on top and one tab on the right side.
Step 7
- Using a plastic spudger, lift up the black clips.
- Still using the plastic spudger, detach the gold connector strip and white connector strip.
- Using both hands, pull the camera apart into two pieces.
Using a plastic spudger, lift up the black clips.
Still using the plastic spudger, detach the gold connector strip and white connector strip.
Using both hands, pull the camera apart into two pieces.
Step 8
Lens
- Using a plastic spudger, lift up the black clips.
- Still using the spudger, detach the three gold wire tape connectors from the inside of the camera.
Still using the spudger, detach the three gold wire tape connectors from the inside of the camera.
Step 9
- Remove the three screws from the inside of the camera using a #00 screwdriver.
Remove the three screws from the inside of the camera using a #00 screwdriver.
Step 10
- Using your thumb and forefinger, pull the lens piece straight out from the body of the camera.
Using your thumb and forefinger, pull the lens piece straight out from the body of the camera.
Step 11
Motherboard
- Remove the two Phillips #00 screws on the right side of the camera.
Remove the two Phillips #00 screws on the right side of the camera.
Step 12
- Using a plastic spudger, lift up the black clips.
- Still using the spudger, detach the gold wire tape connectors from the motherboard.
Still using the spudger, detach the gold wire tape connectors from the motherboard.
Step 13
- Desolder the upper right and lower left wires to remove the motherboard.
Desolder the upper right and lower left wires to remove the motherboard.
Step 14
- In order to remove the motherboard, grab each side of it and pull up using your thumb and forefinger.
In order to remove the motherboard, grab each side of it and pull up using your thumb and forefinger.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 6 other contributors
Max McIntyre
Member since: 01/21/2011
526 Reputation
4 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 13-4, Forte Winter 2011
Member of Cal Poly, Team 13-4, Forte Winter 2011
CPSU-FORTE-W11S13G4
6 Members
12 Guides authored
