Difficulty
Moderate
Steps
6
Time Required
30 minutes - 1 hour
Sections
1
- LCD
- 6 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackOlympus PEN E-P5
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Please note: this requires some skills removing and sticking back again adhesive strips. If available, keep some thin biadhesive suitable for electronics at hand, could be necessary for reassembly.
What you need
Step 1
Battery
- Remove battery before starting disassembly.
Remove battery before starting disassembly.
1024
Step 2
LCD assembly
- Use a Phillips #00 screwdriver to remove 5 screws, two from the base of the assembly and 3 from the top.
Use a Phillips #00 screwdriver to remove 5 screws, two from the base of the assembly and 3 from the top.
Step 3
- Use tweezers to peel back the plastic adhesive cover
- Use a spudger to flip back the black bar on the LCD Ribbon ZIF connector
- Gently pull the ribbon cable out with tweezers
- Remove the LCD assembly from the camera body
Use tweezers to peel back the plastic adhesive cover
Use a spudger to flip back the black bar on the LCD Ribbon ZIF connector
Gently pull the ribbon cable out with tweezers
Remove the LCD assembly from the camera body
Step 4
Remove LCD from frame
- Peel back the small copper tab from top right LCD corner
- Gently remove the plastic frame from the LCD (kept together with some glue). Use a spudger if needed.
Peel back the small copper tab from top right LCD corner
Gently remove the plastic frame from the LCD (kept together with some glue). Use a spudger if needed.
Step 5
Remove the IC with ZIF connectors from damaged LCD screen
- Use tweezers to peel back the plastic adhesive strip covering the ribbon cable
- Use a spudger to flip back the black bar from both the ZIF connectors
- Gently pull out the big and the small ribbon cables with tweezers
- Use a hair dryer to loosen the strength of the black biadhesive strip under the IC containing the three ZIF connectors
- VERY GENTLY use a spudger and/or nails to remove the black biadhesive strip and the green IC. Don’t force the IC since you’ll need it to reassemble your device. Leave the biadhesive under the green IC once removed.
Use tweezers to peel back the plastic adhesive strip covering the ribbon cable
Use a spudger to flip back the black bar from both the ZIF connectors
Gently pull out the big and the small ribbon cables with tweezers
Use a hair dryer to loosen the strength of the black biadhesive strip under the IC containing the three ZIF connectors
VERY GENTLY use a spudger and/or nails to remove the black biadhesive strip and the green IC. Don’t force the IC since you’ll need it to reassemble your device. Leave the biadhesive under the green IC once removed.
Step 6
IC reassembly on new LCD screen
- Unpack the new LCD screen
- Insert the big ribbon cable into its ZIF connector and flip the black bar back in its original position. The cable should be held firmly.
- Insert the small ribbon cable into smaller ZIF connector and flip back the black bar in the closed position. Do not force the cable.
- Stick the green IC to the back plate using the biadhesive strip from the original LCD.
- Use an adhesive strip from the original LCD to hold the ribbon cables to the back plate.
- Use another piece of black adhesive strip to stick the small ribbon tab on the top left corner of the back plate.
Unpack the new LCD screen
Insert the big ribbon cable into its ZIF connector and flip the black bar back in its original position. The cable should be held firmly.
Insert the small ribbon cable into smaller ZIF connector and flip back the black bar in the closed position. Do not force the cable.
Stick the green IC to the back plate using the biadhesive strip from the original LCD.
Use an adhesive strip from the original LCD to hold the ribbon cables to the back plate.
Use another piece of black adhesive strip to stick the small ribbon tab on the top left corner of the back plate.
To reassemble your device, follow these instructions in reverse order from step 4.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Gabriel Marcelli
Member since: 01/28/2018
217 Reputation
1 Guide authored
Badges:
5
+2 more badges