Difficulty
Difficult
Steps
10
Time Required
Suggest a time??
Sections
2
- Motherboard
- 7 steps
- Lens
- 3 steps
Flags
Better Introduction
Improve this guide by completing or revising its introduction.
Missing Details
Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.
BackOlympus C-765
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Motherboard
- Use a Phillips #00 screwdriver to remove the single 4mm screw located directly to the right of the viewfinder on the back of the camera.
- Remove the two 2mm screws from the left side panel.
- Remove the single 3mm screw from the right side panel.
- Remove the five 3mm screws from the bottom of the camera.
Use a Phillips #00 screwdriver to remove the single 4mm screw located directly to the right of the viewfinder on the back of the camera.
Remove the two 2mm screws from the left side panel.
Remove the single 3mm screw from the right side panel.
Remove the five 3mm screws from the bottom of the camera.
1024
Step 2
- Rock the two ribbon cables gently out of their sockets.
- For more on disconnecting ribbon cables, look here.
- Grasp and pull the white cable out of its clip with metal tweezers.
- Remove the back panel completely.
Rock the two ribbon cables gently out of their sockets.
For more on disconnecting ribbon cables, look here.
Grasp and pull the white cable out of its clip with metal tweezers.
Remove the back panel completely.
Step 3
- Peel off the black plastic sheets.
- Use the Phillips #00 screwdriver to remove the two 3mm screws holding the motherboard in place.
Peel off the black plastic sheets.
Use the Phillips #00 screwdriver to remove the two 3mm screws holding the motherboard in place.
Step 4
- Remove the ribbon cable directly below the viewfinder.
- Detach the white plastic clip from its socket with a pair of tweezers.
- Disconnect the ribbon cable from the center of the board, near the central hole.
- Disconnect the three ribbon cables from the top right of the motherboard, near the selector wheel. One is on the top of the board, and the other two are on the underside.
- For more information on disconnecting ribbon cables, look here.
Remove the ribbon cable directly below the viewfinder.
Detach the white plastic clip from its socket with a pair of tweezers.
Disconnect the ribbon cable from the center of the board, near the central hole.
Disconnect the three ribbon cables from the top right of the motherboard, near the selector wheel. One is on the top of the board, and the other two are on the underside.
For more information on disconnecting ribbon cables, look here.
Step 5
- Remove the single 3mm ground screw attached to the right side of the camera body using the Phillips #00 screwdriver.
Remove the single 3mm ground screw attached to the right side of the camera body using the Phillips #00 screwdriver.
Step 6
- Use the soldering iron to desolder the connections from the motherboard.
- For more information on desoldering, look here.
- When soldering, avoid touching any of the other components with the soldering iron to prevent damage to the motherboard.
Use the soldering iron to desolder the connections from the motherboard.
For more information on desoldering, look here.
When soldering, avoid touching any of the other components with the soldering iron to prevent damage to the motherboard.
Step 7
- Remove the motherboard from the camera.
Remove the motherboard from the camera.
Step 8
Lens
- Unscrew the two 3mm screws from the right side of the casing.
- Pop the flash up to get access to the two body screws underneath.
- Undo the two 3mm screws.
Unscrew the two 3mm screws from the right side of the casing.
Pop the flash up to get access to the two body screws underneath.
Undo the two 3mm screws.
Step 9
- Gently pull on the battery casing and the A/V ports to remove the connected components.
- Remove the small ribbon cable from the right side of the casing.
Gently pull on the battery casing and the A/V ports to remove the connected components.
Remove the small ribbon cable from the right side of the casing.
Step 10
- Undo the three flat-top 4mm screws.
- Gently pull the lens away from the camera body.
- Clean or replace the lens.
Undo the three flat-top 4mm screws.
Gently pull the lens away from the camera body.
Clean or replace the lens.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 6 other contributors
Mason Morgan
Member since: 04/05/2011
115 Reputation
6 Guides authored
Badges:
9
+6 more badges
Team
Cal Poly, Team 12-33, Maness Spring 2011
Member of Cal Poly, Team 12-33, Maness Spring 2011
CPSU-MANESS-S11S12G33
3 Members
7 Guides authored