Difficulty
Moderate
Steps
11
Time Required
15 minutes
Sections
3
- Battery
- 3 steps
- Screen Frame
- 4 steps
- Screen
- 4 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackOLPC XO-4 Touch
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Turn the laptop upside-down, with the handle facing away from you.
Turn the laptop upside-down, with the handle facing away from you.
1024
Step 2
- Pull the lock tabs towards the green outer edges of the laptop.
- Hold the left lock tab in the unlock position until the battery is completely removed in the next step.
Pull the lock tabs towards the green outer edges of the laptop.
Hold the left lock tab in the unlock position until the battery is completely removed in the next step.
Step 3
- Lift up on the middle of the battery to remove it from the device.
Lift up on the middle of the battery to remove it from the device.
Step 4
Screen Frame
- Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side.
- Rotate the screen 180° and remove the other two screws.
- You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.
Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side.
Rotate the screen 180° and remove the other two screws.
You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.
Step 5
- Remove the green side panel by pressing down on the small green button on the top and sliding the panel up.
- Repeat the step above for the panel on the other side.
Remove the green side panel by pressing down on the small green button on the top and sliding the panel up.
Repeat the step above for the panel on the other side.
Step 6
- Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.
- Gently lift up the lower part of the frame and pull it down to free the screen frame.
Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.
Gently lift up the lower part of the frame and pull it down to free the screen frame.
Step 7
- Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.
Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.
Step 8
Screen
- Remove the four 7.62mm screws using a Phillips #1 screwdriver.
Remove the four 7.62mm screws using a Phillips #1 screwdriver.
Step 9
- Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break.
- Carefully lift the screen out.
Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break.
Carefully lift the screen out.
Step 10
- Notice that the laptop in this picture has been turned 180° with the antennas now below the screen.
- For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.
Notice that the laptop in this picture has been turned 180° with the antennas now below the screen.
For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.
Step 11
- Remove the screen from the laptop.
Remove the screen from the laptop.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 7 other contributors
Zach Yasuda
Member since: 01/24/2013
173 Reputation
2 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 3-29, Amido Winter 2013
Member of Cal Poly, Team 3-29, Amido Winter 2013
CPSU-AMIDO-W13S3G29
4 Members
20 Guides authored
