Olpc Xo 1 5 Power Button Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 minutes

Sections

Battery
3 steps
Screen
7 steps
Wireless Card
6 steps
Motherboard
3 steps
Power Button
1 step

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

BackOLPC XO-1.5
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Place the laptop upside down with the handle away from you.

Place the laptop upside down with the handle away from you.

1024

Step 2

Slide the tabs out, towards the green edges, to show the open lock symbol.
The right tab will stay in place, but the left tab must be held in position while you remove the battery.

Slide the tabs out, towards the green edges, to show the open lock symbol.

The right tab will stay in place, but the left tab must be held in position while you remove the battery.

Step 3

Lift the middle of the battery to remove it.

Lift the middle of the battery to remove it.

Step 4

              Screen

Turn the laptop so it is resting on its bottom.
Open the laptop by rotating the green wings on the side up, then lifting the top half of the laptop.
Rotate the top half of the laptop about 90 degrees.

Turn the laptop so it is resting on its bottom.

Open the laptop by rotating the green wings on the side up, then lifting the top half of the laptop.

Rotate the top half of the laptop about 90 degrees.

Step 5

Turn the laptop upside down, so you can see the screws on the bottom of the top half.
Remove the two 4mm screws with a Phillips #1 screwdriver.
Rotate the top half 180 degrees.
Remove the two 4mm screws with a Phillips #1 screwdriver.

Turn the laptop upside down, so you can see the screws on the bottom of the top half.

Remove the two 4mm screws with a Phillips #1 screwdriver.

Rotate the top half 180 degrees.

Step 6

Rotate the top of the laptop 90 degrees, so that it is facing you again.
Slide the green pieces off the device. They should come off easily.

Rotate the top of the laptop 90 degrees, so that it is facing you again.

Slide the green pieces off the device. They should come off easily.

Step 7

Pull down on the white screen cover. It does not require much force.
Remove the screen cover.
The game pad on the left sometimes falls during this step.

Pull down on the white screen cover. It does not require much force.

Remove the screen cover.

The game pad on the left sometimes falls during this step.

Step 8

Unscrew the four 7.62mm Phillips #1 screws on either side of the screen.
The screen is still connected by ribbon cables. You can damage the cables if you remove the screen before disconnecting the cables.
Move the screen down a little to expose the ribbon cables.

Unscrew the four 7.62mm Phillips #1 screws on either side of the screen.

The screen is still connected by ribbon cables. You can damage the cables if you remove the screen before disconnecting the cables.

Move the screen down a little to expose the ribbon cables.

Step 9

Flip up the tab right under the middle top of the screen.
Pull the black ribbon cable out of the socket.

Flip up the tab right under the middle top of the screen.

Pull the black ribbon cable out of the socket.

Step 10

Flip up the smaller tab under the left side of the screen.
Remove the small cable to separate the screen from the rest of the laptop.
Gently remove the screen.

Flip up the smaller tab under the left side of the screen.

Remove the small cable to separate the screen from the rest of the laptop.

Gently remove the screen.

Step 11

              Wireless Card

Remove the four 4mm Phillips #1 screws that hold the top cover to the case.

Remove the four 4mm Phillips #1 screws that hold the top cover to the case.

Step 12

Close the lid and rotate the device 180°.
Press firmly on the top two corners of the outside cover. Then slide it down, away from the antennas.

Close the lid and rotate the device 180°.

Press firmly on the top two corners of the outside cover. Then slide it down, away from the antennas.

Step 13

Remove the five 4mm Phillips #1 screws securing the EMI shield to the motherboard.
Gently lift up and remove the EMI shield.

Remove the five 4mm Phillips #1 screws securing the EMI shield to the motherboard.

Gently lift up and remove the EMI shield.

Step 14

Gently remove the two antenna cables by lightly pulling the cable connectors up.

Gently remove the two antenna cables by lightly pulling the cable connectors up.

Step 15

Remove the two 5mm Phillips #1 screws holding the wireless card to the motherboard.
The wireless card will pop up at an angle.

Remove the two 5mm Phillips #1 screws holding the wireless card to the motherboard.

The wireless card will pop up at an angle.

Step 16

Remove the wireless card by gently lifting it out of the socket.

Remove the wireless card by gently lifting it out of the socket.

Step 17

              Motherboard

Disconnect the five cables that connect the motherboard to the case by pulling them straight out of their sockets.
The motherboard is still attached to the case by a microphone cable. Do not remove the motherboard or you will damage the cable.

Disconnect the five cables that connect the motherboard to the case by pulling them straight out of their sockets.

The motherboard is still attached to the case by a microphone cable. Do not remove the motherboard or you will damage the cable.

Step 18

Rotate the device 180° and open the lid.
Disconnect the microphone cable by pulling its connector straight out of its socket on the motherboard.

Rotate the device 180° and open the lid.

Disconnect the microphone cable by pulling its connector straight out of its socket on the motherboard.

Step 19

Close the lid and rotate the device 180°.
Lift the left edge of the motherboard and remove it from the case.
Make sure that the microphone and headphone jack don’t catch on the case as you are removing the motherboard.

Lift the left edge of the motherboard and remove it from the case.

Make sure that the microphone and headphone jack don’t catch on the case as you are removing the motherboard.

Step 20

              Power Button

Push the four power button retaining clips through the bottom of the case with the tip of a screwdriver.
Open the lid, rotate it 180° degrees, and close it again.
Be careful not to lose the small spring that sits inside the power button.

Push the four power button retaining clips through the bottom of the case with the tip of a screwdriver.

Open the lid, rotate it 180° degrees, and close it again.

Be careful not to lose the small spring that sits inside the power button.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 6 other contributors

                    Wei Xia

Member since: 01/25/2013

518 Reputation

                                      5 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Cal Poly, Team 3-28, Amido Winter 2013                        

                                                  Member of Cal Poly, Team 3-28, Amido Winter 2013 



                    CPSU-AMIDO-W13S3G28                     


                                            3 Members                     


                                            10 Guides authored

Needs Better Images#

Markup Mishap#

Introduction#

What you need#

Team#

Needs Better Images

Markup Mishap

Introduction

What you need

Team