Difficulty
Moderate
Steps
9
Time Required
15 - 35 minutes
Sections
2
- Facial Interface
- 6 steps
- Lens
- 3 steps
Flags
0
BackOculus Rift CV1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Facial Interface
- Pull firmly from the top of the headset facial interface to remove the foam frame.
Pull firmly from the top of the headset facial interface to remove the foam frame.
1024
Step 2
- Remove the six T3 4mm screws from the top and bottom edges of the case.
Remove the six T3 4mm screws from the top and bottom edges of the case.
Step 3
- Insert the spudger underneath the edge of the lens on the left or right side.
- Slide the spudger upwards and around the edge of the frame to undo the tabs underneath.
- Repeat for the other side of the frame.
Insert the spudger underneath the edge of the lens on the left or right side.
Slide the spudger upwards and around the edge of the frame to undo the tabs underneath.
Repeat for the other side of the frame.
Step 4
- Lift up the frame to see a tab hidden underneath the lycra mesh along the edge of the lens.
- Pull up on the tab with the spudger.
- Repeat for the corresponding tab on the other lens.
Lift up the frame to see a tab hidden underneath the lycra mesh along the edge of the lens.
Pull up on the tab with the spudger.
Repeat for the corresponding tab on the other lens.
Step 5
- Lift up on the plastic frame around the lens.
- Slide a finger around the inside edge, pulling outward from the center of the lens to release the other tabs.
- Repeat for the frame on the other lens.
Lift up on the plastic frame around the lens.
Slide a finger around the inside edge, pulling outward from the center of the lens to release the other tabs.
Repeat for the frame on the other lens.
Step 6
- Pull up along the outer frame.
- Remove the facial interface.
Pull up along the outer frame.
Remove the facial interface.
Step 7
Lens
- Move the lenses as close together as possible by sliding the button on the bottom of the frame towards the center of the frame.
- Remove the four Phillips #00 4mm screws from the outer edge of the base of the lenses.
- There are two screws that are near the lens that are difficult to see. Remove the screw that is the nearest to the lens. Do not remove the larger screw farther from the lens.
Move the lenses as close together as possible by sliding the button on the bottom of the frame towards the center of the frame.
Remove the four Phillips #00 4mm screws from the outer edge of the base of the lenses.
There are two screws that are near the lens that are difficult to see. Remove the screw that is the nearest to the lens. Do not remove the larger screw farther from the lens.
Step 8
- Push off the 8 tabs (4 per lens) from the base of the lens using a spudger.
- Spread the lenses back apart using the button on the bottom of the headset to access the center tabs more easily.
Push off the 8 tabs (4 per lens) from the base of the lens using a spudger.
Spread the lenses back apart using the button on the bottom of the headset to access the center tabs more easily.
Step 9
- Stretch the headset frame apart to make the lenses more accessible.
- Be careful when removing the lens not to scratch the screen that is directly underneath.
- While the headset frame is spread apart, pull the corner of the lens out. The rest of the lens will unlatch.
- Pull out the lens.
- Repeat for the other lens.
Stretch the headset frame apart to make the lenses more accessible.
Be careful when removing the lens not to scratch the screen that is directly underneath.
While the headset frame is spread apart, pull the corner of the lens out. The rest of the lens will unlatch.
Pull out the lens.
Repeat for the other lens.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Jennifer Lai
Member since: 01/24/2019
226 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
Cal Poly, Team S18-G4, White Winter 2019
Member of Cal Poly, Team S18-G4, White Winter 2019
CPSU-WHITE-W19S18G4
3 Members
10 Guides authored
Night Gryphon - Aug 5, 2019
Reply
Where can i get spare lens?