Difficulty

Moderate

Steps

8

Time Required

                          5 minutes

Sections

2

  • Nutri Ninja Ninja Blender Duo BL641 Body Disassembly
  • 5 steps
  • Fan
  • 3 steps

Flags

0

  • BackNutri Ninja Ninja Blender Duo BL641

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Nutri Ninja Ninja Blender Duo BL641 Body Disassembly
  • Turn blender upside down

Turn blender upside down

1024

Step 2

  • Remove these six screws (0.5 inch 5 gauge phillip’s head)
  • Note: 2 of the screws will be star shaped circled in blue
  • Lift the bottom panel off

Remove these six screws (0.5 inch 5 gauge phillip’s head)

Note: 2 of the screws will be star shaped circled in blue

Lift the bottom panel off

Step 3

  • Unscrew and remove these six phillip’s screws. (0.5 inch 5 gauge phillips)
  • Note: The screws circled in blue are 1/8" longer and have a slightly different top than the rest. These are the only two screws that are different than the rest.

Unscrew and remove these six phillip’s screws. (0.5 inch 5 gauge phillips)

Note: The screws circled in blue are 1/8" longer and have a slightly different top than the rest. These are the only two screws that are different than the rest.

Step 4

  • Insert pry tool in between the two plastic pieces to separate them
  • Move pry tool back and forth from right to left until the two pieces begin to separate as shown.
  • Pry the two pieces apart with your hands as shown in the picture to finish separating the pieces.

Insert pry tool in between the two plastic pieces to separate them

Move pry tool back and forth from right to left until the two pieces begin to separate as shown.

Pry the two pieces apart with your hands as shown in the picture to finish separating the pieces.

Step 5

  • This completes the disassembly of the main body of the blender so you can continue to perform replacements on the internal parts.

This completes the disassembly of the main body of the blender so you can continue to perform replacements on the internal parts.

Step 6

              Fan
  • Remove this hex nut with the adjustable wrench.
  • Be sure to hold the fan still GENTLY while unscrewing the nut so the bolt does not spin with the nut.
  • Fan may be a little sharp

Remove this hex nut with the adjustable wrench.

Be sure to hold the fan still GENTLY while unscrewing the nut so the bolt does not spin with the nut.

Fan may be a little sharp

Step 7

  • Grab the washer with pliers and twist/pull it off of the threaded rod.
  • The washer is not threaded but has rubbery glue holding it to the threaded rod. This is why unscrewing as well as pulling is necessary.

Grab the washer with pliers and twist/pull it off of the threaded rod.

The washer is not threaded but has rubbery glue holding it to the threaded rod. This is why unscrewing as well as pulling is necessary.

Step 8

  • Grab the fan gently and pull it off

Grab the fan gently and pull it off

To reassemble your device, follow these instructions in reverse order along with the body disassembly guide.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Nathan

Member since: 09/26/2017

201 Reputation

                                      2 Guides authored                  



                       Badges:
                       3

Team

                       Cal Poly, Team S7-G1, Banghart Fall 2017                        

                                                  Member of Cal Poly, Team S7-G1, Banghart Fall 2017 



                    CPSU-BANGHART-F17S7G1                     


                                            5 Members                     


                                            6 Guides authored

Victor Sosa - Oct 18, 2018

Reply

Buenas noches.

¿Cómo puedo comprar una tarjeta de esta licuadora?