Nostalgia Electrics Rhp 310 Wiring Repair Repair Guide

Difficulty

Very difficult

Steps

Time Required

                          30 - 40 minutes

Sections

Power Switch
6 steps
Replacing Housing
2 steps
Replacing Fan
5 steps
Nostalgia Electrics RHP-310 Wiring Repair
4 steps

Flags

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Confusing Text

Some of this guide’s text is confusing, duplicated, or off-topic. Clarify it by editing!

Better Introduction

Improve this guide by completing or revising its introduction.

BackNostalgia Electrics RHP-310
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Power Switch

Unplug the popper.
Remove the plastic lid by lifting the lid up.

Unplug the popper.

Remove the plastic lid by lifting the lid up.

1024

Step 2

Lay the popper on its side.
Remove the five 12mm Philips #2 screws around the perimeter of the base with the Phillips #2 phillips head screwdriver.
Remove the two 15mm Philips #2 screws in the center of the base with the Phillips #2 phillips head screwdriver.
Save the screws you remove from the base in a safe place. They will be needed to reattach the housing to the base.

Lay the popper on its side.

Remove the five 12mm Philips #2 screws around the perimeter of the base with the Phillips #2 phillips head screwdriver.

Remove the two 15mm Philips #2 screws in the center of the base with the Phillips #2 phillips head screwdriver.

Save the screws you remove from the base in a safe place. They will be needed to reattach the housing to the base.

Step 3

Flip the base to view the interior surface of the base.
Unscrew the two screws (10 mm Philips #2 screws) from the base.
Remove the base and set it aside.

Flip the base to view the interior surface of the base.

Unscrew the two screws (10 mm Philips #2 screws) from the base.

Remove the base and set it aside.

Step 4

Locate the power switch connected to the side of the housing.
Carefully pinch the sides of the power switch.
Push the power button up and out of the housing.

Locate the power switch connected to the side of the housing.

Carefully pinch the sides of the power switch.

Push the power button up and out of the housing.

Step 5

Now that the power switch is removed from the housing, you must remove the wires connected to the power switch.
Use the plastic opening tool to gently pry the wires loose from the power switch.
The wires should easily pop out from the power switch.

Now that the power switch is removed from the housing, you must remove the wires connected to the power switch.

Use the plastic opening tool to gently pry the wires loose from the power switch.

The wires should easily pop out from the power switch.

Step 6

Remove the power switch from the device.
You can now replace the power switch if necessary.

Remove the power switch from the device.

You can now replace the power switch if necessary.

Step 7

              Replacing Housing

Now that the power switch is disconnected from the popper, you will need to remove the white top.
Gently remove the heating component from the popper.
Unscrew the four screws (11mm Philips #2 screws) that connect the white top to the housing.

Now that the power switch is disconnected from the popper, you will need to remove the white top.

Gently remove the heating component from the popper.

Unscrew the four screws (11mm Philips #2 screws) that connect the white top to the housing.

Step 8

Remove the white top from the housing.
Save the screws from previous step. You will need them to connect the new housing to the white top.

Remove the white top from the housing.

Save the screws from previous step. You will need them to connect the new housing to the white top.

Step 9

              Replacing Fan

Now that the white top is disconnected from the housing, remove the heating component from inside the device.

Now that the white top is disconnected from the housing, remove the heating component from inside the device.

Step 10

Unscrew the three screws (10 mm Philips #2 screws) that hold the heating component together.

Unscrew the three screws (10 mm Philips #2 screws) that hold the heating component together.

Step 11

Make sure to keep the screws. You will need them to put the heating component back together.
Pull the heating component apart.

Make sure to keep the screws. You will need them to put the heating component back together.

Pull the heating component apart.

Step 12

Locate the fan.
Pull the fan off the motor firmly but gently.
When you pull the fan off the motor, be careful. Do not pull to hard or you will break the motor.

Locate the fan.

Pull the fan off the motor firmly but gently.

When you pull the fan off the motor, be careful. Do not pull to hard or you will break the motor.

Step 13

You can now replace the fan.
If there is debris stuck in the fan, you can easily clean it out from the fan in this step.

You can now replace the fan.

If there is debris stuck in the fan, you can easily clean it out from the fan in this step.

Step 14

              Nostalgia Electrics RHP-310 Wiring Repair

Take the heating coil out of complete heating component.

Take the heating coil out of complete heating component.

Step 15

Visually check the wires for frayed wires.
Make sure that the wires are completely connected to a port.

Visually check the wires for frayed wires.

Make sure that the wires are completely connected to a port.

Step 16

If you see a wire that is not connected, solder it back into place.
These websites might be helpful in soldering: Wikipedia Theoatc
Also, use a digital multi-meter to check to make sure there is a current through the wire. If the meter does not read, you might need to replace all the wires.
This website may be helpful in with wiring: How Stuff Works

If you see a wire that is not connected, solder it back into place.

These websites might be helpful in soldering: Wikipedia Theoatc

Also, use a digital multi-meter to check to make sure there is a current through the wire. If the meter does not read, you might need to replace all the wires.

This website may be helpful in with wiring: How Stuff Works

Step 17

This website will help with reconnecting wires:eHow

This website will help with reconnecting wires:eHow

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Dana Clarke

Member since: 09/26/2012

50 Reputation

                                      6 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 16-57, Forte Fall 2012                        

                                                  Member of Cal Poly, Team 16-57, Forte Fall 2012 



                    CPSU-FORTE-F12S16G57                     


                                            5 Members                     


                                            6 Guides authored

Bullets!#

Confusing Text#

Better Introduction#

What you need#

Team#

Bullets!

Confusing Text

Better Introduction

What you need

Team