Nokia Lumia 928 Rear Facing Camera Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 - 35 minutes

Sections

Back Cover
2 steps
Motherboard
4 steps
Rear Facing Camera
2 steps

Flags

BackNokia Lumia 928
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Cover

Power down the phone.
There is a screw located inside the 3.5mm headphone jack that needs to be loosened. Use a Torx T5 screwdriver for this.
The screw does not come out. Once loosened, It will unlock the lock bar inside the phone. You will break it if you do not complete this step properly.
Remove the sim card tray on the top of the phone.
Remove the 4.5 mm Torx T5 screw highlighted with a red circle in the picture. (Note: all screws that you will remove in the phone will be the same)
There is a sticker located on the screw that needs to be peeled off. This voids your warranty.

Power down the phone.

There is a screw located inside the 3.5mm headphone jack that needs to be loosened. Use a Torx T5 screwdriver for this.

The screw does not come out. Once loosened, It will unlock the lock bar inside the phone. You will break it if you do not complete this step properly.

Remove the sim card tray on the top of the phone.

Remove the 4.5 mm Torx T5 screw highlighted with a red circle in the picture. (Note: all screws that you will remove in the phone will be the same)

There is a sticker located on the screw that needs to be peeled off. This voids your warranty.

1024

Step 2

Using the plastic opening tools, you can start to release the plastic clips around the phone. Start in the top left corner, work your way down the left side. Then do the top and bottom of the phone, and finally the right side.
It can be useful to flip the plastic opening tool upside down in certain areas of the phone to make releasing the plastic clips easier.
Once all the clips are released, remove the back cover of the phone.

Using the plastic opening tools, you can start to release the plastic clips around the phone. Start in the top left corner, work your way down the left side. Then do the top and bottom of the phone, and finally the right side.

It can be useful to flip the plastic opening tool upside down in certain areas of the phone to make releasing the plastic clips easier.

Once all the clips are released, remove the back cover of the phone.

Step 3

              Motherboard

Remove all 10 T5 screws on the motherboard. All screws are 4.5 mm Torx T5 screws.

Remove all 10 T5 screws on the motherboard. All screws are 4.5 mm Torx T5 screws.

Step 4

Remove the ribbon connector with a highlighted with a red circle with the plastic opening tool.
Be very careful with the ribbon connectors as they can easily be ripped off.
The ribbon connector highlighted in yellow has a zero insertion force connector. This has a black flap on the end that needs to be flipped up before the ribbon cable can be pulled out.

Remove the ribbon connector with a highlighted with a red circle with the plastic opening tool.

Be very careful with the ribbon connectors as they can easily be ripped off.

The ribbon connector highlighted in yellow has a zero insertion force connector. This has a black flap on the end that needs to be flipped up before the ribbon cable can be pulled out.

Step 5

Remove USB port cover using the plastic opening tool, or your hand. It can be removed easily.

Remove USB port cover using the plastic opening tool, or your hand. It can be removed easily.

Step 6

Pull up the left side of the motherboard.
There is 1 connector that needs to be removed with the plastic opening tool highlighted with a red rectangle. Do not pull the motherboard away from the display assembly until you have removed it.
You have now removed the motherboard from the display assembly and the back cover.

Pull up the left side of the motherboard.

There is 1 connector that needs to be removed with the plastic opening tool highlighted with a red rectangle. Do not pull the motherboard away from the display assembly until you have removed it.

You have now removed the motherboard from the display assembly and the back cover.

Step 7

              Rear Facing Camera

Lift up the connector for the rear facing camera using the plastic opening tool.

Lift up the connector for the rear facing camera using the plastic opening tool.

Step 8

Push the camera out from the side that has the camera housing sticking out (the side in the picture) using the rear end of the plastic opening tool, or your pinkie finger.
You have now removed the rear facing camera.

Push the camera out from the side that has the camera housing sticking out (the side in the picture) using the rear end of the plastic opening tool, or your pinkie finger.

You have now removed the rear facing camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Curtis Dawe

Member since: 03/04/2016

461 Reputation

                                      4 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       UMass Dartmouth, Team 6-8, Bhusal Spring 2016                        

                                                  Member of UMass Dartmouth, Team 6-8, Bhusal Spring 2016 



                    UMASSD-BHUSAL-S16S6G8                     


                                            4 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team