Nokia Lumia 928 Front Facing Camera Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          5 - 10 minutes

Sections

Back Cover
2 steps
Front Facing Camera
2 steps

Flags

BackNokia Lumia 928
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Cover

Power down the phone.
There is a screw located inside the 3.5mm headphone jack that needs to be loosened. Use a Torx T5 screwdriver for this.
The screw does not come out. Once loosened, It will unlock the lock bar inside the phone. You will break it if you do not complete this step properly.
Remove the sim card tray on the top of the phone.
Remove the 4.5 mm Torx T5 screw highlighted with a red circle in the picture. (Note: all screws that you will remove in the phone will be the same)
There is a sticker located on the screw that needs to be peeled off. This voids your warranty.

Power down the phone.

There is a screw located inside the 3.5mm headphone jack that needs to be loosened. Use a Torx T5 screwdriver for this.

The screw does not come out. Once loosened, It will unlock the lock bar inside the phone. You will break it if you do not complete this step properly.

Remove the sim card tray on the top of the phone.

Remove the 4.5 mm Torx T5 screw highlighted with a red circle in the picture. (Note: all screws that you will remove in the phone will be the same)

There is a sticker located on the screw that needs to be peeled off. This voids your warranty.

1024

Step 2

Using the plastic opening tools, you can start to release the plastic clips around the phone. Start in the top left corner, work your way down the left side. Then do the top and bottom of the phone, and finally the right side.
It can be useful to flip the plastic opening tool upside down in certain areas of the phone to make releasing the plastic clips easier.
Once all the clips are released, remove the back cover of the phone.

Using the plastic opening tools, you can start to release the plastic clips around the phone. Start in the top left corner, work your way down the left side. Then do the top and bottom of the phone, and finally the right side.

It can be useful to flip the plastic opening tool upside down in certain areas of the phone to make releasing the plastic clips easier.

Once all the clips are released, remove the back cover of the phone.

Step 3

              Front Facing Camera

Remove both ends of the ribbon connector using a plastic opening tool.
The end highlighted with an orange circle in the picture must slide out towards the edge of the phone.
Be very careful with the ribbon connectors as they can easily be broken.

Remove both ends of the ribbon connector using a plastic opening tool.

The end highlighted with an orange circle in the picture must slide out towards the edge of the phone.

Be very careful with the ribbon connectors as they can easily be broken.

Step 4

Remove the ribbon connector for the front facing camera using the plastic opening tool. Once you have done this, you can lift out the front facing camera with the ribbon connector.
The ribbon connector is held down with some glue, so peel it off slowly to avoid damaging it.
You have now successfully removed the front facing camera.

Remove the ribbon connector for the front facing camera using the plastic opening tool. Once you have done this, you can lift out the front facing camera with the ribbon connector.

The ribbon connector is held down with some glue, so peel it off slowly to avoid damaging it.

You have now successfully removed the front facing camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Curtis Dawe

Member since: 03/04/2016

461 Reputation

                                      4 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       UMass Dartmouth, Team 6-8, Bhusal Spring 2016                        

                                                  Member of UMass Dartmouth, Team 6-8, Bhusal Spring 2016 



                    UMASSD-BHUSAL-S16S6G8                     


                                            4 Members                     


                                            6 Guides authored

Introduction#

What you need#

#

#

#

#

#

#

Team#

#

Introduction

What you need

Team