Nokia Lumia 925 Battery Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          40 minutes

Sections

Motherboard
6 steps
Display
1 step
Speaker
2 steps
Front Camera
2 steps
Battery
7 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackNokia Lumia 925
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Motherboard

Remove the sim card holder by inserting tweezers into the hole. Push down and the holder will spring back up.
Pull out the holder until it is completely separate.
Something like a paperclip will work if there are no tweezers available.

Remove the sim card holder by inserting tweezers into the hole. Push down and the holder will spring back up.

Pull out the holder until it is completely separate.

Something like a paperclip will work if there are no tweezers available.

1024

Step 2

Slide a plastic opening tool under the back cover.
Slide the tool around the outsides of the cover to fully dislodge the pins holding the cover to the phone.
Some pins are facing the opposite way from the others.

Slide a plastic opening tool under the back cover.

Slide the tool around the outsides of the cover to fully dislodge the pins holding the cover to the phone.

Some pins are facing the opposite way from the others.

Step 3

Remove the 3 screws using the T7 Torx screwdriver.
Unclip the black tab connector.

Remove the 3 screws using the T7 Torx screwdriver.

Unclip the black tab connector.

Step 4

Remove the silver metal cover.
Be careful of the tape under the right square side of the panel. Using a spudger helps.

Remove the silver metal cover.

Be careful of the tape under the right square side of the panel. Using a spudger helps.

Step 5

Unclip the two orange tabs.
Remove the four silver screws using the T5 Torx screwdriver.

Unclip the two orange tabs.

Remove the four silver screws using the T5 Torx screwdriver.

Step 6

Remove the motherboard by sliding tweezers between it and the back of the screen. Lift up.

Remove the motherboard by sliding tweezers between it and the back of the screen. Lift up.

Step 7

              Display

Push the screen from the inside of the phone.
Pull the screen off.
Slide the electronic strip through the small opening.

Push the screen from the inside of the phone.

Pull the screen off.

Slide the electronic strip through the small opening.

Step 8

              Speaker

Locate the grey speaker/camera cover.
Carefully remove the cover with either a pair of tweezers or your fingers.

Locate the grey speaker/camera cover.

Carefully remove the cover with either a pair of tweezers or your fingers.

Step 9

With a pair of tweezers, gently remove the orange colored tab closest to the speaker.

With a pair of tweezers, gently remove the orange colored tab closest to the speaker.

Step 10

              Front Camera

Pull at the orange section until it becomes loose.
It is located in the upper leftmost section of the phone behind the front camera.

Pull at the orange section until it becomes loose.

It is located in the upper leftmost section of the phone behind the front camera.

Step 11

Pull vertically on the same orange section until the front camera comes out.
The front camera as well as the speaker may come out after the last step so be careful.

Pull vertically on the same orange section until the front camera comes out.

The front camera as well as the speaker may come out after the last step so be careful.

Step 12

              Battery

Remove the two black screws by using the T5 Torx screwdriver.

Remove the two black screws by using the T5 Torx screwdriver.

Step 13

Carefully pull the metal rod out.

Carefully pull the metal rod out.

Step 14

Pry off the speaker.
Apply heavy pressure, and pull towards the battery.

Pry off the speaker.

Apply heavy pressure, and pull towards the battery.

Step 15

Unclip the black wire.

Unclip the black wire.

Step 16

Peel off the electronic strip.
Be careful not to tear.

Peel off the electronic strip.

Be careful not to tear.

Step 17

Pry off the metal vibrating unit using tweezers.
This requires a lot of force.

Pry off the metal vibrating unit using tweezers.

This requires a lot of force.

Step 18

Insert the tweezers under the corner of the battery, and lift out.
You have successfully removed the battery.

Insert the tweezers under the corner of the battery, and lift out.

You have successfully removed the battery.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 3 other contributors

                    Guillermo Lara

Member since: 09/18/2018

391 Reputation

                                      3 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       University of North Texas, Team S4-G6, Raign Fall 2018                        

                                                  Member of University of North Texas, Team S4-G6, Raign Fall 2018 



                    UNT-RAIGN-F18S4G6                     


                                            4 Members                     


                                            10 Guides authored

Jackson Reynolds - Nov 27, 2018

Add markers to steps 10 and 11 for clarity. Add the battery to the “parts” section. For step 5 make sure the bullet color matches the marking color. Remember to add an introduction.

malcolm redwood - Mar 21, 2022

\Some steps unnecessary e.g. remving the screen.

Also some other parts.

Use your brain.

Better Introduction#

What you need#

Team#

Better Introduction

What you need

Team