Difficulty
Moderate
Steps
13
Time Required
30 minutes
Sections
3
- Back panel
- 5 steps
- Battery
- 5 steps
- Volume, camera, and power ribbon.
- 3 steps
Flags
0
BackNokia Lumia 920
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Remove the Bottom Screws
- Make sure the phone is off.
- Use the T5 screwdriver to remove the two 8.6mm long screws, located at the bottom of the phone. (Head size is 2.5mm)
Make sure the phone is off.
Use the T5 screwdriver to remove the two 8.6mm long screws, located at the bottom of the phone. (Head size is 2.5mm)
1024
Step 2
- Use the smallest Torx screwdriver or another small poking tool and push into the hole on the SIM card slot. The plastic SIM protective piece should pop out quite easily.
- Put that plastic piece aside.
Use the smallest Torx screwdriver or another small poking tool and push into the hole on the SIM card slot. The plastic SIM protective piece should pop out quite easily.
Put that plastic piece aside.
Step 3
- Once both screws on the bottom are removed, and the plastic SIM protective piece is removed, gently push on the outside of the screen.
- The screen should become separated using little force. And should like the pictures shown once complete.
Once both screws on the bottom are removed, and the plastic SIM protective piece is removed, gently push on the outside of the screen.
The screen should become separated using little force. And should like the pictures shown once complete.
Step 4
- This step may be easier to remove the battery first, but it is not mandatory.
- Place the spudger tool or flat plastic tool on top of the ribbon cable to avoid damaging it when prying up on the metal clip.
- Use a plastic opening tool, or gently use a small metal flat-head screwdriver to pry up the metal clip. (It is recommended to use a plastic tool; However, if the opening tool does not work or fit into the small opening underneath the clip, use the flat-head.)
This step may be easier to remove the battery first, but it is not mandatory.
Place the spudger tool or flat plastic tool on top of the ribbon cable to avoid damaging it when prying up on the metal clip.
Use a plastic opening tool, or gently use a small metal flat-head screwdriver to pry up the metal clip. (It is recommended to use a plastic tool; However, if the opening tool does not work or fit into the small opening underneath the clip, use the flat-head.)
Step 5
- Once the metal clip is removed, gently pry up on the ribbon cable connection, located underneath the metal clip you have just removed.
Once the metal clip is removed, gently pry up on the ribbon cable connection, located underneath the metal clip you have just removed.
Step 6
Battery
- Prerequisite step: Back panel removal
- Use the T4 torx screwdriver to remove the 3mm screw (diameter of the head is 1.5mm) fastened to the metal clip, holding the battery in place.
Prerequisite step: Back panel removal
Use the T4 torx screwdriver to remove the 3mm screw (diameter of the head is 1.5mm) fastened to the metal clip, holding the battery in place.
Step 7
- Using the plastic opening tool, pry up on the metal clip holding the battery in place.
- Completely remove the clip.
Using the plastic opening tool, pry up on the metal clip holding the battery in place.
Completely remove the clip.
Step 8
- Use a plastic opening tool. Start on the right, and gently lift up on the copper strip.
- You do not have to completely remove the copper strip, only enough so that the connection to the battery is visible.
Use a plastic opening tool. Start on the right, and gently lift up on the copper strip.
You do not have to completely remove the copper strip, only enough so that the connection to the battery is visible.
Step 9
- Use a plastic opening tool or spudger, and gently lift up on the connective piece.
Use a plastic opening tool or spudger, and gently lift up on the connective piece.
Step 10
- Use a plastic opening tool at the bottom of the battery and gently lift.
- The battery should lift out easily.
Use a plastic opening tool at the bottom of the battery and gently lift.
The battery should lift out easily.
Step 11
Volume, camera, and power ribbon.
- Prerequisite guides: Back panel removal, Battery Removal
- Use the plastic opening tool to gently lift up on the connective piece attached to the volume, camera, and power button strip.
Prerequisite guides: Back panel removal, Battery Removal
Use the plastic opening tool to gently lift up on the connective piece attached to the volume, camera, and power button strip.
Step 12
- Flip the front panel on its side with the strip you are working on facing upward.
- Use a spudger tool and starting at the top, gently pry the button sensors up.
- Slide the tool underneath the strip and pry up the next button sensor.
- Do this down the line until the strip becomes completely detached.
Flip the front panel on its side with the strip you are working on facing upward.
Use a spudger tool and starting at the top, gently pry the button sensors up.
Slide the tool underneath the strip and pry up the next button sensor.
Do this down the line until the strip becomes completely detached.
Step 13
- The power strip should look like this fully detached.
The power strip should look like this fully detached.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
6 other people completed this guide.
Author
with 3 other contributors
Jonathan
Member since: 10/31/2014
1,492 Reputation
4 Guides authored
Badges:
9
+6 more badges
Team
UMass Dartmouth, Team 4-2, Miles Fall 2014
Member of UMass Dartmouth, Team 4-2, Miles Fall 2014
UMASSD-MILES-F14S4G2
2 Members
7 Guides authored