Difficulty

Moderate

Steps

14

Time Required

                          10 - 20 minutes

Sections

4

  • Screen
  • 5 steps
  • Front Camera
  • 1 step
  • Battery
  • 2 steps
  • Speaker
  • 6 steps

Flags

0

  • BackNokia Lumia 900

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Screen
  • Insert the pointed end of the spudger into the sim card port indicated by the picture. Then proceed to remove the sim card port entirely.

Insert the pointed end of the spudger into the sim card port indicated by the picture. Then proceed to remove the sim card port entirely.

1024

Step 2

  • Use tweezers to remove the small rod in the port indicated in the picture.

Use tweezers to remove the small rod in the port indicated in the picture.

Step 3

  • Separate the screen from the motherboard by prying it open with the spudger along with pulling upwards with the suction cup.

Separate the screen from the motherboard by prying it open with the spudger along with pulling upwards with the suction cup.

Step 4

  • Gently pull apart the screen from the motherboard, with only the ribbons connected from the motherboard to the screen.

Gently pull apart the screen from the motherboard, with only the ribbons connected from the motherboard to the screen.

Step 5

  • Disconnect the No-fuss cables from the motherboard by gently prying them up using the flat end of the black stick spudger. Make sure not to bend or crease the cable.
  • Remove the screen.

Disconnect the No-fuss cables from the motherboard by gently prying them up using the flat end of the black stick spudger. Make sure not to bend or crease the cable.

Remove the screen.

Step 6

              Front Camera
  • Use the iFixit iOpener or another heat source to gently heat the top left corner until the adhesive under the camera softens.
  • Use the plastic opening tools to carefully lift the front camera from the motherboard.

Use the iFixit iOpener or another heat source to gently heat the top left corner until the adhesive under the camera softens.

Use the plastic opening tools to carefully lift the front camera from the motherboard.

Step 7

              Battery
  • Use the flat end of a spudger to carefully disconnect the ribbon cable.
  • Make sure not to bend or crease the cable.

Use the flat end of a spudger to carefully disconnect the ribbon cable.

Make sure not to bend or crease the cable.

Step 8

  • Use the flat end of a spudger to remove the battery.
  • The battery may be glued down. This will be evident if the battery is difficult to lift. Use the iFixit iOpener to heat the back of the phone allowing the glue to heat and become more pliable before trying to lift the battery again. This may take several minutes.

Use the flat end of a spudger to remove the battery.

The battery may be glued down. This will be evident if the battery is difficult to lift. Use the iFixit iOpener to heat the back of the phone allowing the glue to heat and become more pliable before trying to lift the battery again. This may take several minutes.

Step 9

              Speaker
  • Use the plastic opening tool to lift the orange ribbon cable from the motherboard.

Use the plastic opening tool to lift the orange ribbon cable from the motherboard.

Step 10

  • Use the plastic opening tool to lift the motherboard out of the casing.
  • It is recommended that you wedge the opening tool in the crevice between the motherboard and casing in the top righthand corner of the device.

Use the plastic opening tool to lift the motherboard out of the casing.

It is recommended that you wedge the opening tool in the crevice between the motherboard and casing in the top righthand corner of the device.

Step 11

  • Use the flat end of a spudger to lift the LED out of the casing.

Use the flat end of a spudger to lift the LED out of the casing.

Step 12

  • Use the flat end of a spudger to lift the metal backplate from the casing.
  • Be sure not to lose the buttons.

Use the flat end of a spudger to lift the metal backplate from the casing.

Be sure not to lose the buttons.

Step 13

  • Wedge the pointed end of the spudger into the gaps in the antenna housing and pull the antenna housing away from the casing walls.

Wedge the pointed end of the spudger into the gaps in the antenna housing and pull the antenna housing away from the casing walls.

Step 14

  • Insert the pointed end of the spudger into the hole and slide the speaker housing out from the casing.

Insert the pointed end of the spudger into the hole and slide the speaker housing out from the casing.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Kourtney Collier

Member since: 03/31/2022

289 Reputation

                                      3 Guides authored                  



                       Badges:
                       3

Team

                       IUPUI, Team 3-2, Harley Spring 2022                        

                                                  Member of IUPUI, Team 3-2, Harley Spring 2022 



                    IUPUI-HARLEY-S22S3G2                     


                                            3 Members                     


                                            6 Guides authored