Nokia Lumia 830 Main Camera Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 - 6 minutes

Sections

Battery
2 steps
Main Speaker
4 steps
Motherboard
3 steps
Main Camera
1 step

Flags

BackNokia Lumia 830
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Place the phone with the screen facing down.
Remove the back cover by placing your fingernail or plastic opening tool under the slotted indent at the bottom of the phone.

Place the phone with the screen facing down.

Remove the back cover by placing your fingernail or plastic opening tool under the slotted indent at the bottom of the phone.

1024

Step 2

Carefully remove the battery by placing the plastic opening tool underneath the indent at the bottom of the battery, and pry it up.
There may be adhesive underneath the battery to keep it in place, this may make it a bit difficult to remove the battery.

Carefully remove the battery by placing the plastic opening tool underneath the indent at the bottom of the battery, and pry it up.

There may be adhesive underneath the battery to keep it in place, this may make it a bit difficult to remove the battery.

Step 3

              Main Speaker

Remove the black strips on both sides of the battery compartment.

Remove the black strips on both sides of the battery compartment.

Step 4

Remove the two 3.9mm silver screws from the bottom corner of the phone. Then remove the five 2.5mm black screws from top to bottom of the phone.
All of the screws take a t5 star screwdriver.

Remove the two 3.9mm silver screws from the bottom corner of the phone. Then remove the five 2.5mm black screws from top to bottom of the phone.

All of the screws take a t5 star screwdriver.

Step 5

Use the plastic opening tool to push into the slots holding the backing in place.
All five slots are along the inner wall of the battery compartment. Push the slots on the sides first before pushing the slot on the top.
Remove the backing from the frame, making sure to lift the bottom portion away from the phone, to allow the top to slide out of place.

Use the plastic opening tool to push into the slots holding the backing in place.

All five slots are along the inner wall of the battery compartment. Push the slots on the sides first before pushing the slot on the top.

Remove the backing from the frame, making sure to lift the bottom portion away from the phone, to allow the top to slide out of place.

Step 6

Lift the speaker out of the phone. You may need to wiggle the speaker loose.

Lift the speaker out of the phone. You may need to wiggle the speaker loose.

Step 7

              Motherboard

Hold the phone in place and grab the metal end of the RF cable with the precise tweezers.
The RF cable is the long, skinny cable that runs down the side of the phone
Be sure to pull the cord up gently, so it is not damaged.

Hold the phone in place and grab the metal end of the RF cable with the precise tweezers.

The RF cable is the long, skinny cable that runs down the side of the phone

Be sure to pull the cord up gently, so it is not damaged.

Step 8

Optional Remove the copper tape at the top right corner of the phone with the precise tweezers.
Scoop one end of the tweezers underneath the skinny part of the tape and peel up.
This tape is not stuck in any way with the vibrator motor. It will lift with the motherboard. Removal is not necessary

Optional Remove the copper tape at the top right corner of the phone with the precise tweezers.

Scoop one end of the tweezers underneath the skinny part of the tape and peel up.

This tape is not stuck in any way with the vibrator motor. It will lift with the motherboard. Removal is not necessary

Step 9

There are five flex connectors located on the motherboard. They look like rectangular metal boxes with a thin strip connected to them.
Unclip the connectors from the motherboard using the plastic opening tool. Lightly press the wedge end of the tool to the opposite site of the connector with the strip attached to it, and pry it up.
Place the plastic opening tool underneath the motherboard near where the three prongs stick out of the bottom and push the motherboard up to remove it.

There are five flex connectors located on the motherboard. They look like rectangular metal boxes with a thin strip connected to them.

Unclip the connectors from the motherboard using the plastic opening tool. Lightly press the wedge end of the tool to the opposite site of the connector with the strip attached to it, and pry it up.

Place the plastic opening tool underneath the motherboard near where the three prongs stick out of the bottom and push the motherboard up to remove it.

Step 10

              Main Camera

After you’ve removed the motherboard, locate the camera connector at the bottom right hand corner of the motherboard, as shown in the image.
Gently use the plastic opening tool to lift the connectors, disconnecting the camera from the motherboard.
Lastly, use tweezers to remove completely.

After you’ve removed the motherboard, locate the camera connector at the bottom right hand corner of the motherboard, as shown in the image.

Gently use the plastic opening tool to lift the connectors, disconnecting the camera from the motherboard.

Lastly, use tweezers to remove completely.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 2 other contributors

                    saydeking

Member since: 10/03/2016

527 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team 1-2, Sullivan Fall 2016                        

                                                  Member of USF Tampa, Team 1-2, Sullivan Fall 2016 



                    USFT-SULLIVAN-F16S1G2                     


                                            3 Members                     


                                            11 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team