Difficulty
Moderate
Steps
13
Time Required
20 - 30 minutes
Sections
1
- LCD Display, Touch screen Glass
- 13 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackNokia Lumia 620
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Before ordering the new Touch screen check the revision (you can see it on the digitizer flex cable, near to the connector).
__________________________ Video manual: __________________________
What you need
Video Overview
Step 1
Switch Off
- Switch off the phone, remove the battery and SIM (Memory) card.
- The lower back cover is held by 3x T4 Torx screws.
- The screws are of two types!
Switch off the phone, remove the battery and SIM (Memory) card.
The lower back cover is held by 3x T4 Torx screws.
The screws are of two types!
1024
Step 2
Lower Back Cover
- Loudspeaker
- Touch screen flex cable connector
- LCD Display flex cable connector
Loudspeaker
Touch screen flex cable connector
LCD Display flex cable connector
Step 3
Touch screen Test
- If you want to replace the Digitizer, let’s test the spare part first.
- Be careful, don’t break the flex cable.
If you want to replace the Digitizer, let’s test the spare part first.
Be careful, don’t break the flex cable.
Step 4
- Another three screws hold the Upper Back Cover.
- Disconnect the Touch screen and the Digitizer flex cables.
Another three screws hold the Upper Back Cover.
Disconnect the Touch screen and the Digitizer flex cables.
Step 5
- If you have not yet disconnected the Digitizer and the Touch screen flex cables, do it now.
- The Logic Board is held to the Middle frame by two plastic clips.
If you have not yet disconnected the Digitizer and the Touch screen flex cables, do it now.
The Logic Board is held to the Middle frame by two plastic clips.
Step 6
- With a plastic tool gently release the mother board and remove it.
With a plastic tool gently release the mother board and remove it.
Step 7
- Front Camera and Proximity & Light sensor module
- Earpiece
- Remove them one by one.
Front Camera and Proximity & Light sensor module
Earpiece
Remove them one by one.
Step 8
- The Midle frame is held by 6x locking clips, three on each side. Release them and remove the Middle frame.
The Midle frame is held by 6x locking clips, three on each side. Release them and remove the Middle frame.
Step 9
- Now gently remove the LCD Display.
- If you have a broken LCD, replace it and reassemble the phone.
- We will continue with removing the Touch screen Glass.
Now gently remove the LCD Display.
If you have a broken LCD, replace it and reassemble the phone.
We will continue with removing the Touch screen Glass.
Step 10
- Put a scotch tape to prevent the glass from scattering.
- With a hot air warm the glass to soften the adhesive.
- You can use a hair dryer for this operation.
- Start with separating at the middle, where the bonded area is smaller.
Put a scotch tape to prevent the glass from scattering.
With a hot air warm the glass to soften the adhesive.
You can use a hair dryer for this operation.
Start with separating at the middle, where the bonded area is smaller.
Step 11
- Continue with the separation by using a plastic tool.
Continue with the separation by using a plastic tool.
Step 12
- Clean the remnants of the old adhesive tape.
- If the spare parts come without adhesive tape, you must put by himself.
- Prepare the new digitizer glass and install it.
- Reassemble the device.
Clean the remnants of the old adhesive tape.
If the spare parts come without adhesive tape, you must put by himself.
Prepare the new digitizer glass and install it.
Reassemble the device.
Step 13
- That’s all.
- .
- .
- .
- .
- .
- .
- Did you do it successfully?
That’s all.
.
Did you do it successfully?
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
13 other people completed this guide.
Author
ZFix
Member since: 12/09/2013
187,195 Reputation
330 Guides authored
Badges:
35
+32 more badges
Team
Master Techs
Member of Master Techs
Community
310 Members
1,168 Guides authored
tave - Jan 25, 2017
Reply
great guide! I made it quite easily, thanks so much
priyamotors - Jun 6, 2018
Reply
i am purchase urgent