Nokia 6086 Vibrator Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 minutes

Sections

Battery
3 steps
Upper Back Cover
4 steps
Base of The Phone
3 steps
Vibrator
4 steps

Flags

BackNokia 6086
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Turn off the phone.
Check if there is a microSD card in the slot behind the door on the side. If so, remove it by first pushing it in, then pulling it out.
Position the phone so that the back side is in view.

Turn off the phone.

Check if there is a microSD card in the slot behind the door on the side. If so, remove it by first pushing it in, then pulling it out.

Position the phone so that the back side is in view.

1024

Step 2

Remove the back battery cover.
Apply pressure on the cover while simultaneously sliding the cover downward.

Remove the back battery cover.

Apply pressure on the cover while simultaneously sliding the cover downward.

Step 3

Insert the iPod opening tool between the base of the phone and the phone battery.
Position the phone so that the battery won’t fall out of the phone.
The battery lifts out of the phone fast and easily.
Carefully lift the battery out of the phone.

Insert the iPod opening tool between the base of the phone and the phone battery.

Position the phone so that the battery won’t fall out of the phone.

The battery lifts out of the phone fast and easily.

Carefully lift the battery out of the phone.

Step 4

              Upper Back Cover

Turn the phone so that the back of the phone is facing forward.
The picture to the left shows the location of the plastic tabs that attach to the upper cover of the phone.
In this picture, the upper cover has already been removed.

Turn the phone so that the back of the phone is facing forward.

The picture to the left shows the location of the plastic tabs that attach to the upper cover of the phone.

In this picture, the upper cover has already been removed.

Step 5

Place the iPod opening tool under the tabs near the top of the phone.
Slide the iPod Opening Tool upwards.
This will pop the tabs and release the upper part of the phone.
Repeat for the left and the right sides.

Place the iPod opening tool under the tabs near the top of the phone.

Slide the iPod Opening Tool upwards.

This will pop the tabs and release the upper part of the phone.

Repeat for the left and the right sides.

Step 6

Place the iPod opening tool at the top area of the bottom section of the phone (indicated in picture).
Lift the iPod opening tool to pop open the clips.
This will release the upper back cover of the phone.
Repeat for the left and the right sides.

Place the iPod opening tool at the top area of the bottom section of the phone (indicated in picture).

Lift the iPod opening tool to pop open the clips.

This will release the upper back cover of the phone.

Step 7

Push upward on the top back cover using two thumbs.
This will remove the top back cover from the phone.

Push upward on the top back cover using two thumbs.

This will remove the top back cover from the phone.

Step 8

              Base of The Phone

Locate the four screws.
Remove the screws using a T6 Torx screwdriver.

Locate the four screws.

Remove the screws using a T6 Torx screwdriver.

Step 9

Turn the phone over.
Gently pull apart the phone.
Start at the bottom of the phone and pull outward.
There are plastic catches on the middle of each side. These should pop free as you pull.
Be careful, the phone will separate into two sections.

Turn the phone over.

Gently pull apart the phone.

Start at the bottom of the phone and pull outward.

There are plastic catches on the middle of each side. These should pop free as you pull.

Be careful, the phone will separate into two sections.

Step 10

The phone should now be in two different sections.
1. The logic board and the back cover
1. The keypad and the rest of the phone

The phone should now be in two different sections.

The logic board and the back cover
The keypad and the rest of the phone

Step 11

              Vibrator

Remove the logic board from the bottom casing.

Remove the logic board from the bottom casing.

Step 12

The logic board should be fully detached from the phone.
The turquoise colored vibrator should now be visible.

The logic board should be fully detached from the phone.

The turquoise colored vibrator should now be visible.

Step 13

Place the tweezers at the base of the vibrator.
Squeeze the tweezers while simultaneously lifting them up to remove the vibrator.

Place the tweezers at the base of the vibrator.

Squeeze the tweezers while simultaneously lifting them up to remove the vibrator.

Step 14

The vibrator should be detached from the phone.

The vibrator should be detached from the phone.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors

                    Caitlin Rahm

Member since: 04/15/2010

78 Reputation

                                      4 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Cal Poly, Team 26-30, Regan Spring 2010                        

                                                  Member of Cal Poly, Team 26-30, Regan Spring 2010 



                    CPSU-REGAN-S10S26G30                     


                                            4 Members                     


                                            17 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team