Difficulty
Easy
Steps
10
Time Required
10 - 15 minutes
Sections
1
- Screen
- 10 steps
Flags
0
BackNokia 6061
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Screen
- Gather the necessary tools:
- T6 Torx screwdriver
- Plastic opening tool
- Small flathead screwdriver
Gather the necessary tools:
T6 Torx screwdriver
Plastic opening tool
Small flathead screwdriver
1024
Step 2
- This guide will show you how to replace the LCD—after it’s been dropped one too many times.
This guide will show you how to replace the LCD—after it’s been dropped one too many times.
Step 3
- Using a 2.0 flathead screwdriver, pry open and remove the black, plastic strip (beneath the screen) to reveal the 2 screws holding the screen in place.
Using a 2.0 flathead screwdriver, pry open and remove the black, plastic strip (beneath the screen) to reveal the 2 screws holding the screen in place.
Step 4
- Remove the two T6 Torx screws from the base of the display.
Remove the two T6 Torx screws from the base of the display.
Step 5
- Once the screws are removed, flip the phone shut.
- Insert the plastic opening tool at the position indicated and pry along the seam between the front cover and display.
- Continue prying along the perimeter of the front cover until it is free from the phone.
Once the screws are removed, flip the phone shut.
Insert the plastic opening tool at the position indicated and pry along the seam between the front cover and display.
Continue prying along the perimeter of the front cover until it is free from the phone.
Step 6
- Use a plastic opening tool to pry the LCD circuit board up and out of the phone.
- Be careful not to damage the circuit board.
- Flip the display up and over to expose its ribbon cable connector.
Use a plastic opening tool to pry the LCD circuit board up and out of the phone.
Be careful not to damage the circuit board.
Flip the display up and over to expose its ribbon cable connector.
Step 7
- Use a plastic opening tool to gently pry the LCD ribbon cable connector up out its socket on the LCD circuit board.
- The other two photos show the male and female sides of the small green connector. Make sure they snap together tightly when the new display is attached.
Use a plastic opening tool to gently pry the LCD ribbon cable connector up out its socket on the LCD circuit board.
The other two photos show the male and female sides of the small green connector. Make sure they snap together tightly when the new display is attached.
Step 8
- To reassemble your phone, reattach the display to the phone by reconnecting the display ribbon cable. Place the screen assembly back into the front case of the phone.
To reassemble your phone, reattach the display to the phone by reconnecting the display ribbon cable. Place the screen assembly back into the front case of the phone.
Step 9
- Replace the phone cover by applying pressure until a click is heard.
Replace the phone cover by applying pressure until a click is heard.
Step 10
- With the cover reattached, flip the phone into the open position and replace the screws removed in step 3. The screw-holes are indicated in the photo.
- Replace the black, plastic strip by applying pressure until the strip audibly clicks into place.
With the cover reattached, flip the phone into the open position and replace the screws removed in step 3. The screw-holes are indicated in the photo.
Replace the black, plastic strip by applying pressure until the strip audibly clicks into place.
Cancel: I did not complete this guide.
Author
with 12 other contributors
rosin7
Member since: 02/14/2013
55 Reputation
2 Guides authored
Badges:
4
+1 more badge
Team
Ohio State, Team 1-3, Buehl Spring 2013
Member of Ohio State, Team 1-3, Buehl Spring 2013
OSU-BUEHL-S13S1G3
4 Members
4 Guides authored
