Difficulty
Moderate
Steps
11
Time Required
30 minutes
Sections
2
- Display Assembly
- 8 steps
- Home Button Assembly
- 3 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackNokia 6
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Display Assembly
- Power off your Nokia 6 before beginning disassembly.
- Insert the SIM card ejection tool into the hole on the left side of the phone.
- Remove the SIM card and microSD card.
Power off your Nokia 6 before beginning disassembly.
Insert the SIM card ejection tool into the hole on the left side of the phone.
Remove the SIM card and microSD card.
1024
Step 2
- If your display glass is cracked, take precaution by taping over the display to prevent further breakage and harm.
- Lay overlapping strips of clear packing tape over the Nokia 6’s display until the whole screen is covered.
If your display glass is cracked, take precaution by taping over the display to prevent further breakage and harm.
Lay overlapping strips of clear packing tape over the Nokia 6’s display until the whole screen is covered.
Step 3
- To soften the adhesive, use a heat gun and heat one edge of the phone for five minutes.
- To use the heat gun, plug it into an outlet.
- When the heat gun is plugged in, the heat gun automatically turns on and will start blowing hot air.
To soften the adhesive, use a heat gun and heat one edge of the phone for five minutes.
To use the heat gun, plug it into an outlet.
When the heat gun is plugged in, the heat gun automatically turns on and will start blowing hot air.
Step 4
- Take a Jimmy and slide it under the glass after the adhesive has been softened.
- Place a pick under the glass after lifting with the pry tool so that the screen won’t re-adhere to the frame again.
- Make sure to not touch the LCD edge underneath the glass layer with the metal pry tool or the cards. This can damage the ribbon cables underneath and compromise the structural integrity of the phone itself.
- The corners of the screen are the most fragile part of the screen. Make sure that the entire edge of the screen is dislodged from the frame before prying at the corners.
Take a Jimmy and slide it under the glass after the adhesive has been softened.
Place a pick under the glass after lifting with the pry tool so that the screen won’t re-adhere to the frame again.
Make sure to not touch the LCD edge underneath the glass layer with the metal pry tool or the cards. This can damage the ribbon cables underneath and compromise the structural integrity of the phone itself.
The corners of the screen are the most fragile part of the screen. Make sure that the entire edge of the screen is dislodged from the frame before prying at the corners.
Step 5
- Lift the screen off of the phone.
Lift the screen off of the phone.
Step 6
- Use a Phillips #000 screwdriver to remove the 1 mm x 1.4 mm screw holding down the metal bracket over the screen ribbon connector.
Use a Phillips #000 screwdriver to remove the 1 mm x 1.4 mm screw holding down the metal bracket over the screen ribbon connector.
Step 7
- Remove the metal bracket with a tweezer.
Remove the metal bracket with a tweezer.
Step 8
- Use a spudger to disconnect the screen ribbon connector and free the display assembly.
- The corners and edge of the LCD are fragile. Be careful attaching it to the back of the phone.
- Carefully remove the screen from the device.
Use a spudger to disconnect the screen ribbon connector and free the display assembly.
The corners and edge of the LCD are fragile. Be careful attaching it to the back of the phone.
Carefully remove the screen from the device.
Step 9
Home Button Assembly
- Disconnect the battery connector with a spudger.
Disconnect the battery connector with a spudger.
Step 10
- Use a Phillips #00 screwdriver to remove the 1.2 mm x 2.2 mm screw in the upper hand corner of the phone.
- Use tweezers to remove the bracket.
Use a Phillips #00 screwdriver to remove the 1.2 mm x 2.2 mm screw in the upper hand corner of the phone.
Use tweezers to remove the bracket.
Step 11
- Detach the cable with the black nylon spudger.
- Detach the home button and remove it from the device.
Detach the cable with the black nylon spudger.
Detach the home button and remove it from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Chrissy Robins
Member since: 04/15/2019
1,453 Reputation
10 Guides authored
Badges:
12
+9 more badges
Team
Cal Poly, Team S9-G15, Maness Spring 2019
Member of Cal Poly, Team S9-G15, Maness Spring 2019
CPSU-MANESS-S19S9G15
4 Members
10 Guides authored
Britt Isaacs - Jan 10, 2022
Reply
I am very grateful for your help,now I got it all figured out..I can do it own my own without necessary taking it to the Nokia center right here in Kenya. friday night funkin mods online