Nokia 6 Front Facing Camera Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          40 minutes

Sections

Display Assembly
8 steps
Home Button Assembly
3 steps
Midframe
2 steps
Motherboard
4 steps
Front-Facing Camera
2 steps

Flags

BackNokia 6
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Be sure to take extra caution when removing it from the motherboard.

What you need

Step 1

              Display Assembly

Power off your Nokia 6 before beginning disassembly.
Insert the SIM card ejection tool into the hole on the left side of the phone.
Remove the SIM card and microSD card.

Power off your Nokia 6 before beginning disassembly.

Insert the SIM card ejection tool into the hole on the left side of the phone.

Remove the SIM card and microSD card.

1024

Step 2

If your display glass is cracked, take precaution by taping over the display to prevent further breakage and harm.
Lay overlapping strips of clear packing tape over the Nokia 6’s display until the whole screen is covered.

If your display glass is cracked, take precaution by taping over the display to prevent further breakage and harm.

Lay overlapping strips of clear packing tape over the Nokia 6’s display until the whole screen is covered.

Step 3

To soften the adhesive, use a heat gun and heat one edge of the phone for five minutes.
To use the heat gun, plug it into an outlet.
When the heat gun is plugged in, the heat gun automatically turns on and will start blowing hot air.

To soften the adhesive, use a heat gun and heat one edge of the phone for five minutes.

To use the heat gun, plug it into an outlet.

When the heat gun is plugged in, the heat gun automatically turns on and will start blowing hot air.

Step 4

Take a Jimmy and slide it under the glass after the adhesive has been softened.
Place a pick under the glass after lifting with the pry tool so that the screen won’t re-adhere to the frame again.
Make sure to not touch the LCD edge underneath the glass layer with the metal pry tool or the cards. This can damage the ribbon cables underneath and compromise the structural integrity of the phone itself.
The corners of the screen are the most fragile part of the screen. Make sure that the entire edge of the screen is dislodged from the frame before prying at the corners.

Take a Jimmy and slide it under the glass after the adhesive has been softened.

Place a pick under the glass after lifting with the pry tool so that the screen won’t re-adhere to the frame again.

Make sure to not touch the LCD edge underneath the glass layer with the metal pry tool or the cards. This can damage the ribbon cables underneath and compromise the structural integrity of the phone itself.

The corners of the screen are the most fragile part of the screen. Make sure that the entire edge of the screen is dislodged from the frame before prying at the corners.

Step 5

Lift the screen off of the phone.

Lift the screen off of the phone.

Step 6

Use a Phillips #000 screwdriver to remove the 1 mm x 1.4 mm screw holding down the metal bracket over the screen ribbon connector.

Use a Phillips #000 screwdriver to remove the 1 mm x 1.4 mm screw holding down the metal bracket over the screen ribbon connector.

Step 7

Remove the metal bracket with a tweezer.

Remove the metal bracket with a tweezer.

Step 8

Use a spudger to disconnect the screen ribbon connector and free the display assembly.
The corners and edge of the LCD are fragile. Be careful attaching it to the back of the phone.
Carefully remove the screen from the device.

Use a spudger to disconnect the screen ribbon connector and free the display assembly.

The corners and edge of the LCD are fragile. Be careful attaching it to the back of the phone.

Carefully remove the screen from the device.

Step 9

              Home Button Assembly

Disconnect the battery connector with a spudger.

Disconnect the battery connector with a spudger.

Step 10

Use a Phillips #00 screwdriver to remove the 1.2 mm x 2.2 mm screw in the upper hand corner of the phone.
Use tweezers to remove the bracket.

Use a Phillips #00 screwdriver to remove the 1.2 mm x 2.2 mm screw in the upper hand corner of the phone.

Use tweezers to remove the bracket.

Step 11

Detach the cable with the black nylon spudger.
Detach the home button and remove it from the device.

Detach the cable with the black nylon spudger.

Detach the home button and remove it from the device.

Step 12

              Midframe

Remove 18 screws.
There is one 1 mm x 1.4 mm screw that needs to be removed by a Phillips #000 screwdriver.
One of the screws is 1.2 mm x 4.2 mm and will be removed by a Phillips #00.
The remaining 16 screws can be removed by the Phillips #00 screwdriver and are 1.2 mm x 2.2 mm.

Remove 18 screws.

There is one 1 mm x 1.4 mm screw that needs to be removed by a Phillips #000 screwdriver.

One of the screws is 1.2 mm x 4.2 mm and will be removed by a Phillips #00.

The remaining 16 screws can be removed by the Phillips #00 screwdriver and are 1.2 mm x 2.2 mm.

Step 13

Decouple the midframe with the spudger and remove the midframe from the device.

Decouple the midframe with the spudger and remove the midframe from the device.

Step 14

              Motherboard

Remove the bracket with tweezers.

Remove the bracket with tweezers.

Step 15

Detach the two cables with the spudger.
Detach the cable with a pair of tweezers.
Be careful when detaching the cables, make sure to not completely remove the cables from the phone!

Detach the two cables with the spudger.

Detach the cable with a pair of tweezers.

Be careful when detaching the cables, make sure to not completely remove the cables from the phone!

Step 16

Remove six screws.
Two of these screws are 1.0 mm x 1.4 mm and need to be removed by a Phillips #000 screwdriver.
The remaining four screws are 1.2 mm x 2.2 mm and are removed by a Phillips #00 screwdriver.

Remove six screws.

Two of these screws are 1.0 mm x 1.4 mm and need to be removed by a Phillips #000 screwdriver.

The remaining four screws are 1.2 mm x 2.2 mm and are removed by a Phillips #00 screwdriver.

Step 17

Remove the motherboard from the Nokia 6 with the spudger.
Be careful because the motherboard is fragile. Wiggle it gently to remove it.

Remove the motherboard from the Nokia 6 with the spudger.

Be careful because the motherboard is fragile. Wiggle it gently to remove it.

Step 18

              Front-Facing Camera

Turn the motherboard around to see the front-facing camera.

Turn the motherboard around to see the front-facing camera.

Step 19

Remove the 8MP front-facing camera with the spudger.

Remove the 8MP front-facing camera with the spudger.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Chrissy Robins

Member since: 04/15/2019

1,453 Reputation

                                      10 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Cal Poly, Team S9-G15, Maness Spring 2019                        

                                                  Member of Cal Poly, Team S9-G15, Maness Spring 2019 



                    CPSU-MANESS-S19S9G15                     


                                            4 Members                     


                                            10 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team