Difficulty

Moderate

Steps

8

Time Required

Suggest a time??

Sections

3

  • Battery
  • 2 steps
  • Keypad
  • 2 steps
  • Motherboard
  • 4 steps

Flags

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

  • BackNokia 5310b XpressMusic

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Battery
  • Slide the back cover down with your thumb.
  • *Note: the battery cover is not shown in this picture

Slide the back cover down with your thumb.

*Note: the battery cover is not shown in this picture

1024

Step 2

  • Gently lift the battery with a fingernail and remove it from its housing.
  • *Note: the battery may be replaced or repaired at this step

Gently lift the battery with a fingernail and remove it from its housing.

*Note: the battery may be replaced or repaired at this step

Step 3

              Keypad
  • On some models, the front case is screwed down from the back. Follow steps 5 and 6 FIRST to remove the camera cover and two T6 screws, before removing the faceplate.
  • Use the Spudger to gently pry up the edges of the front face plate
  • At the center of the faceplate edge below the music keys there is a small latch on each side.

On some models, the front case is screwed down from the back. Follow steps 5 and 6 FIRST to remove the camera cover and two T6 screws, before removing the faceplate.

Use the Spudger to gently pry up the edges of the front face plate

At the center of the faceplate edge below the music keys there is a small latch on each side.

Step 4

  • Lift up the keypad from the bottom with either the spudger or your finger.
  • Note: at this time the keypad can be removed and replaced

Lift up the keypad from the bottom with either the spudger or your finger.

Note: at this time the keypad can be removed and replaced

Step 5

              Motherboard
  • Gently unsnap the back camera cover from the phone.
  • Lift the cover from the phone after it is unsnapped.

Gently unsnap the back camera cover from the phone.

Lift the cover from the phone after it is unsnapped.

Step 6

  • Use the T6 torx screwdriver head to remove the 2 screws on either side of the camera
  • Flip over the phone and again us the T6 torx head to remove the 4 screws located at each corner of the white keypad base

Use the T6 torx screwdriver head to remove the 2 screws on either side of the camera

Flip over the phone and again us the T6 torx head to remove the 4 screws located at each corner of the white keypad base

Step 7

  • Unclip the faceplate plug (ribbon) located in the lower left corner of the motherboard

Unclip the faceplate plug (ribbon) located in the lower left corner of the motherboard

Step 8

  • Use the Spudger to pry up the 2 metal clips located near the center of the motherboard on both the left and right
  • At this point the phone should come apart into 2 pieces, the motherboard/LCD screen and the faceplate

Use the Spudger to pry up the 2 metal clips located near the center of the motherboard on both the left and right

At this point the phone should come apart into 2 pieces, the motherboard/LCD screen and the faceplate

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 3 other contributors 


                    Max Kirby

Member since: 05/01/2011

518 Reputation

                                      4 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       Cal Poly, Team 15-14, Regan Spring 2011                        

                                                  Member of Cal Poly, Team 15-14, Regan Spring 2011 



                    CPSU-REGAN-S11S15G14                     


                                            3 Members                     


                                            8 Guides authored

Vincent Tschanz - Oct 4, 2011

Reply

Step 5 and 6 must be performed before step 3, otherwise, you will dislodge the thread from the front plate. so you have to remove the camera cover first, remove the 2 screws then you can remove the front plate without breaking anything.