Nokia 3360 Screen Replacement Repair Guide

Difficulty

Easy

Steps

11

Time Required

                          10 - 15 minutes            

Sections

4

• Battery
• 3 steps
• Charger Connector
• 4 steps
• Logic Board
• 1 step
• Screen
• 3 steps

Flags

2

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Missed a Step

Oops! This guide is currently missing some important steps.

• BackNokia 3360

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Press down on the back of the phone with your thumb. Then slide the back plate upward toward the top of the phone.
• Lift the back plate off the phone.

Press down on the back of the phone with your thumb. Then slide the back plate upward toward the top of the phone.

Lift the back plate off the phone.

1024

Step 2

• To release the battery, press the two tabs that are located directly above the battery towards the top of the phone at the same time.

To release the battery, press the two tabs that are located directly above the battery towards the top of the phone at the same time.

Step 3

• Lift the battery out of the phone.
• Note: Upon reassembly of the phone refer to second picture. The bottom of the battery with three square openings should line up with the prongs sticking out of the phone.

Lift the battery out of the phone.

Note: Upon reassembly of the phone refer to second picture. The bottom of the battery with three square openings should line up with the prongs sticking out of the phone.

Step 4

              Charger Connector               

• Use a pry tool towards the bottom of the phone to gently detach the face plate from the dark grey phone frame.
• Hold phone frame down while separating the face plate.
• Separate the faceplate and grey phone frame.

Use a pry tool towards the bottom of the phone to gently detach the face plate from the dark grey phone frame.

Hold phone frame down while separating the face plate.

Separate the faceplate and grey phone frame.

Step 5

• Remove the six screws using a T6 screwdriver. (refer to second picture to help identify T6 screwdriver head).
• NOTE: When reassembling the device be sure to not over tighten the screws.

Remove the six screws using a T6 screwdriver. (refer to second picture to help identify T6 screwdriver head).

NOTE: When reassembling the device be sure to not over tighten the screws.

Step 6

• Place the phone with the screen facing down onto a flat surface.
• Place the flat edge of the pry tool into the seam on the side, just above the screen. (refer to picture on where to place pry tool).
• Push the pry tool into the seam.
• Pry apart the plates until the cover separates from the rest of the phone. Be careful not to apply too much pressure
• Proceed to pull the front cover away from the rest of the phone. (refer to second picture for results) The marking foreshadows what we will be using in the next step.

Place the phone with the screen facing down onto a flat surface.

Place the flat edge of the pry tool into the seam on the side, just above the screen. (refer to picture on where to place pry tool).

Push the pry tool into the seam.

Pry apart the plates until the cover separates from the rest of the phone. Be careful not to apply too much pressure

Proceed to pull the front cover away from the rest of the phone. (refer to second picture for results) The marking foreshadows what we will be using in the next step.

Step 7

• Locate the charger connector. (refer to picture with marker)
• Carefully lift the charger connector upward to detach.
• NOTE: When reassembling this device the charger connector is placed toward the bottom of the phone. The connector has a peg sticking out that fits into the logic board. (refer to third picture)

Locate the charger connector. (refer to picture with marker)

Carefully lift the charger connector upward to detach.

NOTE: When reassembling this device the charger connector is placed toward the bottom of the phone. The connector has a peg sticking out that fits into the logic board. (refer to third picture)

Step 8

              Logic Board               

• Once the charger connector is pulled out, proceed with removing the logic board.
• To remove the logic board, grip the four corners of the logic board and lift from the front inner case.
• Notice the second picture the logic board has been turned over with the button side facing up.
• Note: Upon reassembly the logic board must be placed correctly. The button side with the various circles should face down, lining up with the circular holes on the inner case.

Once the charger connector is pulled out, proceed with removing the logic board.

To remove the logic board, grip the four corners of the logic board and lift from the front inner case.

Notice the second picture the logic board has been turned over with the button side facing up.

Note: Upon reassembly the logic board must be placed correctly. The button side with the various circles should face down, lining up with the circular holes on the inner case.

Step 9

              Screen               

• Do not touch the glass portion of the screen.
• To remove the screen from the front inside case, hold the front case in one hand and with the other depress the upper metal edge of the screen until the screen separates.
• The screen and internal keypad frame are one solid piece.(refer to second picture)

Do not touch the glass portion of the screen.

To remove the screen from the front inside case, hold the front case in one hand and with the other depress the upper metal edge of the screen until the screen separates.

The screen and internal keypad frame are one solid piece.(refer to second picture)

Step 10

• Now that the screen is detached, you can replace the screen.

Now that the screen is detached, you can replace the screen.

Step 11

• Once the screen is replaced, reverse steps to reassemble the phone properly following the additional notes within some of the steps.

Once the screen is replaced, reverse steps to reassemble the phone properly following the additional notes within some of the steps.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.                                             

Author

                                      with 10 other contributors 

                    Kirk Gonzalez                     

Member since: 01/22/2010

218 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       Cal Poly, Team 8-39, Regan Winter 2010                        

                                                  Member of Cal Poly, Team 8-39, Regan Winter 2010 



                    CPSU-REGAN-W10S8G39                     


                                            4 Members                     


                                            12 Guides authored