Nokia 3300B Screen Replacement Repair Guide

Difficulty

Easy

Steps

10

Time Required

                          15 - 20 minutes            

Sections

2

• Battery
• 2 steps
• Screen
• 8 steps

Flags

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Missing Prerequisites

This guide is missing information on how to start the process. Make a prerequisite guide!

• BackNokia 3300B

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Flip the Nokia 3300B over with the back-side facing towards you.
• Gently press the button on the back of the battery cover to release the cover and slide up.

Flip the Nokia 3300B over with the back-side facing towards you.

Gently press the button on the back of the battery cover to release the cover and slide up.

1024

Step 2

• Lift the battery out of the back of the phone.
• It is easiest to lift the battery out of the phone from the right-hand side, as seen in the picture.

Lift the battery out of the back of the phone.

It is easiest to lift the battery out of the phone from the right-hand side, as seen in the picture.

Step 3

              Screen               

• Gently push the blue tabs on the top of the phone out of their slots.
• With the phone facing up, pop the blue faceplate off by using your fingernail (or some tweezers) and working your way around the phone.
• Note: If the blue cover does not detach easily use your finger nails to try and split it open, as seen in the picture.

Gently push the blue tabs on the top of the phone out of their slots.

With the phone facing up, pop the blue faceplate off by using your fingernail (or some tweezers) and working your way around the phone.

Note: If the blue cover does not detach easily use your finger nails to try and split it open, as seen in the picture.

Step 4

• With the screen still facing you, remove the blue faceplate.

With the screen still facing you, remove the blue faceplate.

Step 5

• Grab the sides of the keypad and lift it up vertically.
• If you encounter resistance while removing the keypad, be sure to lift up evenly on both sides, so the button’s pin don’t snap.

Grab the sides of the keypad and lift it up vertically.

If you encounter resistance while removing the keypad, be sure to lift up evenly on both sides, so the button’s pin don’t snap.

Step 6

• Using the Torx T6 bit of a Phillips precision screwdriver, remove the six screws on the phone’s inner protective case, as seen in the picture.
• NOTE: Be sure to save these screws so the phone can be reassembled later.

Using the Torx T6 bit of a Phillips precision screwdriver, remove the six screws on the phone’s inner protective case, as seen in the picture.

NOTE: Be sure to save these screws so the phone can be reassembled later.

Step 7

• Holding the phone with the screen facing you, remove the top half of the phone from the circuit board.

Holding the phone with the screen facing you, remove the top half of the phone from the circuit board.

Step 8

• Hold the top half of the phone with the screen facing you.
• Using a pair of tweezers, release the tabs holding the two distinct cases together.
• The tabs are very fragile. Be gentle when releasing the tabs.

Hold the top half of the phone with the screen facing you.

Using a pair of tweezers, release the tabs holding the two distinct cases together.

The tabs are very fragile. Be gentle when releasing the tabs.

Step 9

• Be sure to remove both casings so that the screen is facing down. This will ensure that the screen does not fall out of its case.
• NOTE: The screen’s part identification sticker is on the top back side of the screen. The screen will need to be replaced with the same orientation.

Be sure to remove both casings so that the screen is facing down. This will ensure that the screen does not fall out of its case.

NOTE: The screen’s part identification sticker is on the top back side of the screen. The screen will need to be replaced with the same orientation.

Step 10

• Tilt the casing back and the screen should fall out smoothly.
• Replace the old screen with the new screen.

Tilt the casing back and the screen should fall out smoothly.

Replace the old screen with the new screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 5 other contributors 

                    Chris Colwell                     

Member since: 04/13/2010

107 Reputation

                                      2 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges                           

Team

                       Cal Poly, Team 18-65, Johann Spring 2010                        

                                                  Member of Cal Poly, Team 18-65, Johann Spring 2010 



                    CPSU-JOHANN-S10S18G65                     


                                            4 Members                     


                                            9 Guides authored