Difficulty
Moderate
Steps
6
Time Required
15 - 30 minutes
Sections
4
- Nokia 2115i Battery
- 2 steps
- Faceplate
- 1 step
- Removing the Keypad
- 1 step
- Removing the Motherboard
- 2 steps
Flags
1
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackNokia 2115i
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Nokia 2115i Battery
- To prevent shock, press down on the power button located on the top of the phone until the phone shuts off.
- Press down on the small gray button located on the back of the phone.
- Slide the back plate down and off.
To prevent shock, press down on the power button located on the top of the phone until the phone shuts off.
Press down on the small gray button located on the back of the phone.
Slide the back plate down and off.
1024
Step 2
- To remove the battery, begin by holding the phone sideways.
- Then, insert your thumb in the groove below the battery and push the battery up and out.
To remove the battery, begin by holding the phone sideways.
Then, insert your thumb in the groove below the battery and push the battery up and out.
Step 3
Faceplate
- Locate the spudger. A photo of the correct spudger is provided to the left.
- Turn the front of the phone to face you. Find the two small square holes on the bottom left and right sides of the faceplate.
- Insert the spudger into each square hole and push up to detach the face plate.
Locate the spudger. A photo of the correct spudger is provided to the left.
Turn the front of the phone to face you. Find the two small square holes on the bottom left and right sides of the faceplate.
Insert the spudger into each square hole and push up to detach the face plate.
Step 4
Removing the Keypad
- Note: The keypad will be loose and may fall off during this step.
- Pull the face plate up and off of the phone.
- To remove the keypad, simply lift it off the phone.
Note: The keypad will be loose and may fall off during this step.
Pull the face plate up and off of the phone.
To remove the keypad, simply lift it off the phone.
Step 5
Removing the Motherboard
- Locate the 6 screws on the metallic sheet that previously held the keypad. (This sheet, shown in the pictures, is the top side of the motherboard).
- Note: 2 of the screws are on the bottom corners, 2 are on the right and left edges of the phone below the screen, and 2 are on the very top corners of the phone, above the screen.
- Warning: The middle two screws are attached to the base of the phone with two black plastic rings. Use tweezers to remove the screws carefully to avoid breaking the plastic rings
- Use a size T6 Torx screwdriver to remove each of these 6 screws.
Locate the 6 screws on the metallic sheet that previously held the keypad. (This sheet, shown in the pictures, is the top side of the motherboard).
Note: 2 of the screws are on the bottom corners, 2 are on the right and left edges of the phone below the screen, and 2 are on the very top corners of the phone, above the screen.
Warning: The middle two screws are attached to the base of the phone with two black plastic rings. Use tweezers to remove the screws carefully to avoid breaking the plastic rings
Use a size T6 Torx screwdriver to remove each of these 6 screws.
Step 6
- To remove the motherboard, lift it up and off the phone.
- Note: The screen will still be attached to the motherboard.
To remove the motherboard, lift it up and off the phone.
Note: The screen will still be attached to the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 6 other contributors
Shane
Member since: 09/30/2010
80 Reputation
6 Guides authored
Badges:
8
+5 more badges
Team
Cal Poly, Team 14-38, Forte Fall 2010
Member of Cal Poly, Team 14-38, Forte Fall 2010
CPSU-FORTE-F10S14G38
5 Members
6 Guides authored
