Difficulty

Moderate

Steps

6

Time Required

Suggest a time??

Sections

1

  • Nivona Caferomatica 770 opening
  • 6 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackNivona Caferomatica 770

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Nivona Caferomatica 770 opening
  • Pull the power plug!
  • Remove all attachments such as water reservoir, coffee compartment lid, trestle drawer. Remove all coffee beans in the storage container.
  • Unscrew the five Torx T10 screws on the back.

Pull the power plug!

Remove all attachments such as water reservoir, coffee compartment lid, trestle drawer. Remove all coffee beans in the storage container.

Unscrew the five Torx T10 screws on the back.

1024

Step 2

  • Unscrew the two Torx T10 screws on the front edge of the heat plate.
  • Do not remove the heat plate completely yet, its supply cables are still connected.
  • Lift the front edge of the heat plate and slide it forward a bit to clear the tabs on the back edge.
  • Put the heat plate back down, but in such a way that you can reach the screws underneath.
  • Unscrew the two Torx T10 screws located under the heat plate.

Unscrew the two Torx T10 screws on the front edge of the heat plate.

Do not remove the heat plate completely yet, its supply cables are still connected.

Lift the front edge of the heat plate and slide it forward a bit to clear the tabs on the back edge.

Put the heat plate back down, but in such a way that you can reach the screws underneath.

Unscrew the two Torx T10 screws located under the heat plate.

Step 3

  • Gently lift the upper side a bit and put it back down.
  • Push the side panel on the water tank back about 2 cm.
  • This may jam a bit.
  • Place the side panel next to the machine. Do not remove it completely yet, the cables of the switch are still connected.
  • Disconnect the flat plugs from the switch. Be sure to note the order of the cables for later reassembly.
  • Remove the side panel.

Gently lift the upper side a bit and put it back down.

Push the side panel on the water tank back about 2 cm.

This may jam a bit.

Place the side panel next to the machine. Do not remove it completely yet, the cables of the switch are still connected.

Disconnect the flat plugs from the switch. Be sure to note the order of the cables for later reassembly.

Remove the side panel.

Step 4

  • Loosen the two insulated flat plugs with which the heat plate is connected.
  • Lift the top slightly upwards and loosen the nut that secures the eyelet to the green-yellow grounding cable. Remove the eyelet.
  • Do not remove the top yet, it is still connected with a sensor cable.

Loosen the two insulated flat plugs with which the heat plate is connected.

Lift the top slightly upwards and loosen the nut that secures the eyelet to the green-yellow grounding cable. Remove the eyelet.

Do not remove the top yet, it is still connected with a sensor cable.

Step 5

  • Lift the top side slightly.
  • Press down the locking tab on the plug of the white sensor cable and pull off the black plug towards the front of the machine.
  • Press the two catches of the counterpart on the sides together and slide it out of the opening towards the back.
  • Now the top is free and you can remove it.

Lift the top side slightly.

Press down the locking tab on the plug of the white sensor cable and pull off the black plug towards the front of the machine.

Press the two catches of the counterpart on the sides together and slide it out of the opening towards the back.

Now the top is free and you can remove it.

Step 6

  • Slide the side panel with the service door back about 2 cm and remove it.
  • This may jam a little.

Slide the side panel with the service door back about 2 cm and remove it.

This may jam a little.

Work through the steps in reverse order to reassemble your device.

Cancel: I did not complete this guide.

        shingle is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

shingle

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges