Difficulty

Moderate

Steps

36

Time Required

                          30 minutes - 1 hour

Sections

5

  • Faceplate
  • 6 steps
  • Outer Case
  • 8 steps
  • DVD Drive
  • 8 steps
  • Motherboard Cover
  • 12 steps
  • Wi-Fi Antennas
  • 2 steps

Flags

0

  • BackNintendo Wii

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Faceplate
  • Use a metal spudger to remove the white plastic screw covers stuck to the lower case near the front of the Wii.

Use a metal spudger to remove the white plastic screw covers stuck to the lower case near the front of the Wii.

1024

Step 2

  • Remove the two 8.3 mm Tri-Wing screws hidden under the covers you just removed.

Remove the two 8.3 mm Tri-Wing screws hidden under the covers you just removed.

Step 3

  • Remove the single 5.9 mm Phillips screw under the controller port door nearest the faceplate.

Remove the single 5.9 mm Phillips screw under the controller port door nearest the faceplate.

Step 4

  • Use a metal spudger to remove the rubber foot stuck to the side of the Wii near the DVD drive opening.

Use a metal spudger to remove the rubber foot stuck to the side of the Wii near the DVD drive opening.

Step 5

  • Remove the single 5.9 mm Phillips screw hidden under the foot you just removed.

Remove the single 5.9 mm Phillips screw hidden under the foot you just removed.

Step 6

  • Carefully pull the faceplate away from the front of the Wii.
  • Use a pair of tweezers to disconnect the LED cable’s plastic connector from the motherboard.
  • Remove the faceplate.

Carefully pull the faceplate away from the front of the Wii.

Use a pair of tweezers to disconnect the LED cable’s plastic connector from the motherboard.

Remove the faceplate.

Step 7

              Outer Case
  • Open the controller port cover until it is perpendicular to the black controller port bezel.
  • Pull the controller port cover straight up to release it from the outer case.
  • Repeat this procedure for the memory card port cover.

Open the controller port cover until it is perpendicular to the black controller port bezel.

Pull the controller port cover straight up to release it from the outer case.

Repeat this procedure for the memory card port cover.

Step 8

  • Remove the two remaining 4.1 mm Phillips screws along the top edge of the black plastic controller port bezel.
  • Lift the bezel from the long edge furthest away from the controller ports and remove it from the Wii.

Remove the two remaining 4.1 mm Phillips screws along the top edge of the black plastic controller port bezel.

Lift the bezel from the long edge furthest away from the controller ports and remove it from the Wii.

Step 9

  • Remove the two 5 mm Phillips screws above the controller ports.

Remove the two 5 mm Phillips screws above the controller ports.

Step 10

  • Use a metal spudger to remove the three highlighted screw covers stuck to the side of the Wii.

Use a metal spudger to remove the three highlighted screw covers stuck to the side of the Wii.

Step 11

  • Remove the following screws:
  • Two 5 mm Phillips screws
  • One 8.2 mm Tri-Wing screw

Remove the following screws:

Two 5 mm Phillips screws

One 8.2 mm Tri-Wing screw

Step 12

  • Use a metal spudger to remove the two rubber feet stuck to the bottom face of the Wii near the rear ports.

Use a metal spudger to remove the two rubber feet stuck to the bottom face of the Wii near the rear ports.

Step 13

  • Remove the two 8.2 mm Tri-Wing screws hidden under the feet you just removed.

Remove the two 8.2 mm Tri-Wing screws hidden under the feet you just removed.

Step 14

  • Lift the outer case straight up off the body of the Wii.

Lift the outer case straight up off the body of the Wii.

Step 15

              DVD Drive
  • Remove the small Phillips screw securing the battery door to the bottom panel.
  • This screw is captive to the battery door.
  • Pull the battery door out of the Wii.
  • This is a good time to change the CR2032 battery if it hasn’t been changed recently.

Remove the small Phillips screw securing the battery door to the bottom panel.

This screw is captive to the battery door.

Pull the battery door out of the Wii.

This is a good time to change the CR2032 battery if it hasn’t been changed recently.

Step 16

  • Remove the 8.2 mm Tri-Wing screw that was hidden beneath the battery door.

Remove the 8.2 mm Tri-Wing screw that was hidden beneath the battery door.

Step 17

  • Remove the two 8.2 mm Tri-Wing screws securing the DVD drive shield near the controller ports.

Remove the two 8.2 mm Tri-Wing screws securing the DVD drive shield near the controller ports.

Step 18

  • Lift the DVD drive shield upward and remove it from the Wii.

Lift the DVD drive shield upward and remove it from the Wii.

Step 19

  • Remove the four 9 mm #1 Phillips screws securing the DVD drive to the bottom panel.

Remove the four 9 mm #1 Phillips screws securing the DVD drive to the bottom panel.

Step 20

  • Lift the side of the DVD drive opposite the controller ports enough to access the cables on its bottom face.
  • Carefully pull the DVD drive power cable out from under the plastic shroud near the heat sink.

Lift the side of the DVD drive opposite the controller ports enough to access the cables on its bottom face.

Carefully pull the DVD drive power cable out from under the plastic shroud near the heat sink.

Step 21

  • Pull the DVD drive power cable away from its socket on the DVD drive.

Pull the DVD drive power cable away from its socket on the DVD drive.

Step 22

  • Use your fingernail to flip up the retaining flap on the DVD drive ribbon cable socket.
  • Be sure you are prying up on the retaining flap, not the socket itself.
  • Pull the DVD drive ribbon cable out of its socket.
  • Remove the DVD drive from the Wii.

Use your fingernail to flip up the retaining flap on the DVD drive ribbon cable socket.

Be sure you are prying up on the retaining flap, not the socket itself.

Pull the DVD drive ribbon cable out of its socket.

Remove the DVD drive from the Wii.

Step 23

              Motherboard Cover
  • Use a pair of tweezers to lift the fan connector up and out of its socket on the logic board.
  • Be sure your tweezers are clamped down on the fan connector, not the socket on the motherboard.

Use a pair of tweezers to lift the fan connector up and out of its socket on the logic board.

Be sure your tweezers are clamped down on the fan connector, not the socket on the motherboard.

Step 24

  • Remove the two 10 mm Phillips screws securing the fan to the fan shroud.
  • Remove the fan from the Wii.

Remove the two 10 mm Phillips screws securing the fan to the fan shroud.

Remove the fan from the Wii.

Step 25

  • Use the tip of a spudger or another fine-pointed tool to carefully pry one of the black plastic retaining fingers attached to the fan shroud away from the Wi-Fi antenna board.
  • Lift the Wi-Fi antenna out of the fan shroud.

Use the tip of a spudger or another fine-pointed tool to carefully pry one of the black plastic retaining fingers attached to the fan shroud away from the Wi-Fi antenna board.

Lift the Wi-Fi antenna out of the fan shroud.

Step 26

  • Remove the single 10 mm Phillips screw securing the second Wi-Fi antenna to the top of the fan shroud.

Remove the single 10 mm Phillips screw securing the second Wi-Fi antenna to the top of the fan shroud.

Step 27

  • Remove the two pieces of tape securing the second Wi-Fi antenna cable to the plastic bracket near the heat sink.

Remove the two pieces of tape securing the second Wi-Fi antenna cable to the plastic bracket near the heat sink.

Step 28

  • Carefully de-route both antennas from the frame of the Wii and lay them aside.

Carefully de-route both antennas from the frame of the Wii and lay them aside.

Step 29

  • Remove the three 10 mm Phillips screws securing the fan shroud to the Wii.
  • Lift the fan shroud off the heat sink and remove it from the Wii.

Remove the three 10 mm Phillips screws securing the fan shroud to the Wii.

Lift the fan shroud off the heat sink and remove it from the Wii.

Step 30

  • Remove the following six screws securing the EMI fingers to the bottom panel:
  • Four 7 mm Phillips screws
  • Two 11.3 mm Phillips screws
  • Remove both sets of EMI fingers from the Wii.

Remove the following six screws securing the EMI fingers to the bottom panel:

Four 7 mm Phillips screws

Two 11.3 mm Phillips screws

Remove both sets of EMI fingers from the Wii.

Step 31

  • Remove the following three screws:
  • One 7 mm Phillips screw
  • Two 10 mm Phillips screws
  • Lift the bracket out of the Wii.

Remove the following three screws:

One 7 mm Phillips screw

Two 10 mm Phillips screws

Lift the bracket out of the Wii.

Step 32

  • Remove the three 10 mm Phillips screws securing the black bracket to the bottom panel near the front of the Wii.
  • Slightly lift the bracket and use your other hand to pull the retaining clip away from where the Wi-Fi antennas enter the motherboard sheild.
  • Remove the bracket from the Wii.
  • Be sure not to lose the small square nut loosely held by the black plastic bracket.

Remove the three 10 mm Phillips screws securing the black bracket to the bottom panel near the front of the Wii.

Slightly lift the bracket and use your other hand to pull the retaining clip away from where the Wi-Fi antennas enter the motherboard sheild.

Remove the bracket from the Wii.

Be sure not to lose the small square nut loosely held by the black plastic bracket.

Step 33

  • Remove the nine remaining 7 mm Phillips screws securing the motherboard cover to the bottom panel.

Remove the nine remaining 7 mm Phillips screws securing the motherboard cover to the bottom panel.

Step 34

  • Carefully lift the motherboard cover off the motherboard, minding any cables that may get caught.
  • On some models, a thermal pad for the wireless chip is attached to the underside of the motherboard cover. Be sure to replace it when reassembling.

Carefully lift the motherboard cover off the motherboard, minding any cables that may get caught.

On some models, a thermal pad for the wireless chip is attached to the underside of the motherboard cover. Be sure to replace it when reassembling.

Step 35

              Wi-Fi Antennas
  • Lift the side of the Wi-Fi board furthest away from the heat sink and lift it out of its socket on the motherboard, being careful not to put too much sideways force on the connector.

Lift the side of the Wi-Fi board furthest away from the heat sink and lift it out of its socket on the motherboard, being careful not to put too much sideways force on the connector.

Step 36

  • Use the flat end of a spudger to pry both antenna connectors off their sockets on the Wi-Fi board.

Use the flat end of a spudger to pry both antenna connectors off their sockets on the Wi-Fi board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Author

                                      with 4 other contributors 


                    Andrew Bookholt

575,478 Reputation

                                      618 Guides authored                  



                       Badges:
                       47







                                                        +44 more badges

Brendan keller - Aug 11, 2017

Reply

After I pry the antenna’s off then what