Difficulty
Moderate
Steps
9
Time Required
40 minutes
Sections
3
- Battery
- 2 steps
- Outer Case
- 2 steps
- Analog Stick
- 5 steps
Flags
0
BackNintendo Wii U GamePad
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Face the GamePad down and unscrew the two Phillips #00 screws which are attached to the battery cover.
- Lift up and remove the battery cover.
Face the GamePad down and unscrew the two Phillips #00 screws which are attached to the battery cover.
Lift up and remove the battery cover.
1024
Step 2
- With your finger on the battery connector, pull downwards toward the base of the GamePad to disconnect it.
- Pull upwards from the bottom of the battery to release it.
With your finger on the battery connector, pull downwards toward the base of the GamePad to disconnect it.
Pull upwards from the bottom of the battery to release it.
Step 3
Outer Case
- Remove the ten 8.9mm Tri-wing Y1 screws hidden underneath square stickers.
- Lift up the back plate.
- The back plate is still connected by a cable to the motherboard.
Remove the ten 8.9mm Tri-wing Y1 screws hidden underneath square stickers.
Lift up the back plate.
The back plate is still connected by a cable to the motherboard.
Step 4
- Unplug the connector that connects the back plate to the motherboard.
- Remove the back plate.
Unplug the connector that connects the back plate to the motherboard.
Remove the back plate.
Step 5
Analog Stick
- Take out the left and right shoulder buttons in the upper corners.
- Remove the ZR and ZL trigger buttons by lifting up and sliding outward.
Take out the left and right shoulder buttons in the upper corners.
Remove the ZR and ZL trigger buttons by lifting up and sliding outward.
Step 6
- Remove the top rubber cover by pulling it off of its mounts to access one of the mounting screws.
- Remove the four 5.2mm Phillips #0 screws.
Remove the top rubber cover by pulling it off of its mounts to access one of the mounting screws.
Remove the four 5.2mm Phillips #0 screws.
Step 7
- Use a spudger to lift the tab which releases the blue ribbon cable.
- Remove the analog stick and button cover.
Use a spudger to lift the tab which releases the blue ribbon cable.
Remove the analog stick and button cover.
Step 8
- Use your thumb and push the connector towards the rightmost edge to disconnect the analog stick cable connector.
Use your thumb and push the connector towards the rightmost edge to disconnect the analog stick cable connector.
Step 9
- Remove the two 9.0mm Tri-wing Y0 screws.
- Lift out the analog stick.
Remove the two 9.0mm Tri-wing Y0 screws.
Lift out the analog stick.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
78 other people completed this guide.
Author
with 8 other contributors
Kim Arre
Member since: 01/11/2013
4,403 Reputation
8 Guides authored
Badges:
20
+17 more badges
Team
Cal Poly, Team 17-20, Forte Winter 2013
Member of Cal Poly, Team 17-20, Forte Winter 2013
CPSU-FORTE-W13S17G20
5 Members
28 Guides authored
Victor Torres - Jun 30, 2013
Reply
where can i find replacement analogs for wiiu gamepad and wiiu procontoller?
mhuntersr - Jul 17, 2016
Frederik Rischmann - Nov 20, 2016
They are available at ebay.com Cost around 7,50 $ Left & Right (different - look what you need). Comes all from china or hong Kong but Quality is 1A (so far i can tell).
maskedpainter - Dec 8, 2013
Reply
Bump previous question because dogs seem to enjoy their texture.
wandererwk - Jan 17, 2014
Reply
Has anyone tried this?
http://dx.com/p/replacement-3d-analog-st…
I know it says for the pro controller. But based from the images, the pins could be compatible.