Difficulty
Moderate
Steps
8
Time Required
25 minutes
Sections
2
- Console Outer Case
- 5 steps
- Front Faceplate
- 3 steps
Flags
0
BackNintendo Wii U
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Console Outer Case
- With the bottom of the console facing up, remove the following 6 screws hidden underneath the white square stickers:
- Three 5.1mm Phillips #000 screws
- Two 6.1mm Tri-wing Y0 screws
- One 13.2mm Tri-wing Y1 screw
With the bottom of the console facing up, remove the following 6 screws hidden underneath the white square stickers:
Three 5.1mm Phillips #000 screws
Two 6.1mm Tri-wing Y0 screws
One 13.2mm Tri-wing Y1 screw
1024
Step 2
- Rotate the console 180 degrees so that the exhaust vents are facing you.
- Remove the two 7.1mm Phillips #00 screws.
Rotate the console 180 degrees so that the exhaust vents are facing you.
Remove the two 7.1mm Phillips #00 screws.
Step 3
- On the side opposite of the exhaust vents, slide the cover faceplate towards the back of the console and pull upwards to release it.
On the side opposite of the exhaust vents, slide the cover faceplate towards the back of the console and pull upwards to release it.
Step 4
- On the bottom of the console beneath the previously removed faceplate, remove the three 13.2mm Tri-wing Y1 screws.
On the bottom of the console beneath the previously removed faceplate, remove the three 13.2mm Tri-wing Y1 screws.
Step 5
- On the back of the console, lift up and release the main top cover.
On the back of the console, lift up and release the main top cover.
Step 6
Front Faceplate
- Rotate the device so that the front plate is facing you.
- On each side of the console, remove the 3.5mm Phillips #0 screw connecting the DVD drive to the faceplate.
Rotate the device so that the front plate is facing you.
On each side of the console, remove the 3.5mm Phillips #0 screw connecting the DVD drive to the faceplate.
Step 7
- Rotate the device so that the front plate is on the right side and the ribbon cable is visible.
- The ribbon cable is connected to the system by a latch which holds in the blue tab. Flip this latch up to unlock it.
- Lift up on the blue tab to release the ribbon cable.
Rotate the device so that the front plate is on the right side and the ribbon cable is visible.
The ribbon cable is connected to the system by a latch which holds in the blue tab. Flip this latch up to unlock it.
Lift up on the blue tab to release the ribbon cable.
Step 8
- Remove the front faceplate.
Remove the front faceplate.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
10 other people completed this guide.
Author
with 6 other contributors
Kim Arre
Member since: 01/11/2013
4,403 Reputation
8 Guides authored
Badges:
20
+17 more badges
Team
Cal Poly, Team 17-20, Forte Winter 2013
Member of Cal Poly, Team 17-20, Forte Winter 2013
CPSU-FORTE-W13S17G20
5 Members
28 Guides authored
Matt Jones - Jan 7, 2014
Reply
Great guide. I was able to fix the front USB door on my Wii u! Thanks guys!
Gutzin Fish - Nov 3, 2016
Reply
My ribbon seems to work but the little connection it plugs into on the circuit board in the console broke off. Not just the black clip but the whole little circuit. Seems like a clean break. Can I solder it back on? If I push it back on and hold the ribbon in the red light comes on and blinks. Occasionally I can get the white light to come on for like a second but I never hear fans spinning/more of the unit coming to life before it shuts itself off.
Thoughts on how to fix it?
Melissa - May 4, 2020
Reply
My daughter shoved change into my disc slot of my Wii I. I thought I got out all pulling through the faceplate dvd slot but now when I put in a game disc it won’t catcalls accept it. It pulls in, sounds like it turns a little bit and then ejects the disc. Could change still be stuck in the reader or do I need to replace it now?