Difficulty
Moderate
Steps
6
Time Required
5 - 10 minutes
Sections
2
- Front Cover Plate and Batteries
- 4 steps
- Main Buttons
- 2 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackWii Remote
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Front Cover Plate and Batteries
- Flip the Wii Remote over so the battery cover faces you.
- Push up on the bottom tab.
- Remove the battery cover.
Flip the Wii Remote over so the battery cover faces you.
Push up on the bottom tab.
Remove the battery cover.
1024
Step 2
- Remove the first battery by pressing down on the positive end and pulling the battery out.
- Remove the second battery by pushing up on the positive end and pulling the battery out.
Remove the first battery by pressing down on the positive end and pulling the battery out.
Remove the second battery by pushing up on the positive end and pulling the battery out.
Step 3
- Using a tri-point Y1 Screwdriver, remove the two center 7mm screws by turning them counterclockwise.
- Repeat with the two bottom screws.
Using a tri-point Y1 Screwdriver, remove the two center 7mm screws by turning them counterclockwise.
Repeat with the two bottom screws.
Step 4
- With the flat end of a spudger, gently apply pressure to the tabs located on left side of the controller.
- These tabs are breakable. However, if the tabs are broken the controller will still function.
- Open the front plate like a book.
- Small parts may fall out as you open the front plate.
With the flat end of a spudger, gently apply pressure to the tabs located on left side of the controller.
These tabs are breakable. However, if the tabs are broken the controller will still function.
Open the front plate like a book.
Small parts may fall out as you open the front plate.
Step 5
Main Buttons
- Working on the inside of the front cover, peel off the three rubber pads covering the buttons.
Working on the inside of the front cover, peel off the three rubber pads covering the buttons.
Step 6
- Flip over the cover, allowing the buttons to fall into your hand.
- Be ready to catch all the buttons, some are very small. If a button does not fall out apply gentle pressure from behind.
- When reassembling, put each plastic button in its allocated slot. Each button only fits snugly in one slot.
- The best option for you is rotate the Wii Controller by 180°. If you obey this note, the small parts wont fall off and then you can remove the buttons.
Flip over the cover, allowing the buttons to fall into your hand.
Be ready to catch all the buttons, some are very small. If a button does not fall out apply gentle pressure from behind.
When reassembling, put each plastic button in its allocated slot. Each button only fits snugly in one slot.
The best option for you is rotate the Wii Controller by 180°. If you obey this note, the small parts wont fall off and then you can remove the buttons.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
15 other people completed this guide.
Author
with 6 other contributors
Emily
Member since: 04/14/2013
1,116 Reputation
6 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 3-44, Amido Spring 2013
Member of Cal Poly, Team 3-44, Amido Spring 2013
CPSU-AMIDO-S13S3G44
4 Members
19 Guides authored
devannedloss - May 20, 2017
Reply
Where did you get your replacement buttons? I can’t find them online anywhere…
Michael Velten - Feb 13, 2022
Me too, can’t find them.