Difficulty
Moderate
Steps
14
Time Required
20 - 40 minutes
Sections
2
- Faceplate
- 6 steps
- Outer Case
- 8 steps
Flags
0
BackNintendo Wii
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Faceplate
- Use a metal spudger to remove the white plastic screw covers stuck to the lower case near the front of the Wii.
Use a metal spudger to remove the white plastic screw covers stuck to the lower case near the front of the Wii.
1024
Step 2
- Remove the two 8.3 mm Tri-Wing screws hidden under the covers you just removed.
Remove the two 8.3 mm Tri-Wing screws hidden under the covers you just removed.
Step 3
- Remove the single 5.9 mm Phillips screw under the controller port door nearest the faceplate.
Remove the single 5.9 mm Phillips screw under the controller port door nearest the faceplate.
Step 4
- Use a metal spudger to remove the rubber foot stuck to the side of the Wii near the DVD drive opening.
Use a metal spudger to remove the rubber foot stuck to the side of the Wii near the DVD drive opening.
Step 5
- Remove the single 5.9 mm Phillips screw hidden under the foot you just removed.
Remove the single 5.9 mm Phillips screw hidden under the foot you just removed.
Step 6
- Carefully pull the faceplate away from the front of the Wii.
- Use a pair of tweezers to disconnect the LED cable’s plastic connector from the motherboard.
- Remove the faceplate.
Carefully pull the faceplate away from the front of the Wii.
Use a pair of tweezers to disconnect the LED cable’s plastic connector from the motherboard.
Remove the faceplate.
Step 7
Outer Case
- Open the controller port cover until it is perpendicular to the black controller port bezel.
- Pull the controller port cover straight up to release it from the outer case.
- Repeat this procedure for the memory card port cover.
Open the controller port cover until it is perpendicular to the black controller port bezel.
Pull the controller port cover straight up to release it from the outer case.
Repeat this procedure for the memory card port cover.
Step 8
- Remove the two remaining 4.1 mm Phillips screws along the top edge of the black plastic controller port bezel.
- Lift the bezel from the long edge furthest away from the controller ports and remove it from the Wii.
Remove the two remaining 4.1 mm Phillips screws along the top edge of the black plastic controller port bezel.
Lift the bezel from the long edge furthest away from the controller ports and remove it from the Wii.
Step 9
- Remove the two 5 mm Phillips screws above the controller ports.
Remove the two 5 mm Phillips screws above the controller ports.
Step 10
- Use a metal spudger to remove the three highlighted screw covers stuck to the side of the Wii.
Use a metal spudger to remove the three highlighted screw covers stuck to the side of the Wii.
Step 11
- Remove the following screws:
- Two 5 mm Phillips screws
- One 8.2 mm Tri-Wing screw
Remove the following screws:
Two 5 mm Phillips screws
One 8.2 mm Tri-Wing screw
Step 12
- Use a metal spudger to remove the two rubber feet stuck to the bottom face of the Wii near the rear ports.
Use a metal spudger to remove the two rubber feet stuck to the bottom face of the Wii near the rear ports.
Step 13
- Remove the two 8.2 mm Tri-Wing screws hidden under the feet you just removed.
Remove the two 8.2 mm Tri-Wing screws hidden under the feet you just removed.
Step 14
- Lift the outer case straight up off the body of the Wii.
Lift the outer case straight up off the body of the Wii.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
33 other people completed this guide.
Author
with 4 other contributors
Andrew Bookholt
575,478 Reputation
618 Guides authored
Badges:
47
+44 more badges
wewomack - Nov 23, 2014
Reply
Great guide. I had no problems.
iamstilllaughing - Jun 14, 2020
Reply
Ugh, I went and purchased an iFixit Essential Electronics Toolkit and the Tri-wing screwdriver is too small! Y000 is what it says on the box, time to return this purchase.
Lily Larceny - Feb 22, 2021
Reply
Unfortunately this guide stops half way through and doesn’t include the other side of the case, which involves quite a few screws as the motherboard is screwed down in quite a few places, and the cpu heatsink has to come up, it’s much more complicated than this.