Difficulty

Moderate

Steps

15

Time Required

                          10 - 15 minutes

Sections

3

  • Battery
  • 6 steps
  • Case
  • 5 steps
  • Trigger Button
  • 4 steps

Flags

0

  • BackNintendo Switch Pro Controller

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove the screws
  • Flip the controller over so the model stickers face the ceiling.
  • Use a JIS 00 driver or an official iFixit PH 00 driver to remove the two black flathead 8.4 mm-long screws that secure the handles, located at the ends of the handles.

Flip the controller over so the model stickers face the ceiling.

Use a JIS 00 driver or an official iFixit PH 00 driver to remove the two black flathead 8.4 mm-long screws that secure the handles, located at the ends of the handles.

1024

Step 2

              Remove the handle covers
  • Carefully remove the handle covers by pulling them away from the main body.

Carefully remove the handle covers by pulling them away from the main body.

Step 3

              Remove the screws
  • Use a Phillips screwdriver to remove the four silver 6.8 mm-long screws that secure the clear back plastic cover.

Use a Phillips screwdriver to remove the four silver 6.8 mm-long screws that secure the clear back plastic cover.

Step 4

              Unclip the plastic cover
  • Carefully pry away the clear plastic cover using your fingernail.

Carefully pry away the clear plastic cover using your fingernail.

Step 5

              Remove the clear plastic cover
  • Remove the clear plastic cover.

Remove the clear plastic cover.

Step 6

              Remove the battery
  • Remove the lithium-ion battery by using a fingernail or plastic opening tool to pry it up on the left side.
  • Only a small amount of force is needed.

Remove the lithium-ion battery by using a fingernail or plastic opening tool to pry it up on the left side.

Only a small amount of force is needed.

Step 7

              Remove the screws
  • Use a Phillips screwdriver to remove the five 5mm-long screws from the back of the controller.

Use a Phillips screwdriver to remove the five 5mm-long screws from the back of the controller.

Step 8

  • Delicately take off the plastic cover from the controller.
  • Do not completely remove the front cover just yet, as it is still attached to the motherboard via a white ribbon cable.

Delicately take off the plastic cover from the controller.

Do not completely remove the front cover just yet, as it is still attached to the motherboard via a white ribbon cable.

Step 9

              Open the flap
  • Use the tip of an opening pick to open the black flap of the ZIF connector by pushing it upwards.

Use the tip of an opening pick to open the black flap of the ZIF connector by pushing it upwards.

Step 10

              Disconnect the interconnect cable
  • Use your fingers or a pair of blunt nose tweezers to disconnect the interconnect cable from its connector.

Use your fingers or a pair of blunt nose tweezers to disconnect the interconnect cable from its connector.

Step 11

              Remove the front case
  • Remove the front case.

Remove the front case.

Step 12

              Remove the screws
  • Remove the two 6.8 mm-long screws on the top circuit board using a Phillips screwdriver.

Remove the two 6.8 mm-long screws on the top circuit board using a Phillips screwdriver.

Step 13

              Open the ZIF connector
  • Use a spudger to flip up the locking tab on the ZIF connector.

Use a spudger to flip up the locking tab on the ZIF connector.

Step 14

  • Remove the black ribbon cable from its connector.
  • Only a small amount of force should be needed to remove the ribbon cable.

Remove the black ribbon cable from its connector.

Only a small amount of force should be needed to remove the ribbon cable.

Step 15

  • Remove the trigger buttons from the plastic cover.

Remove the trigger buttons from the plastic cover.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      11 other people completed this guide.

Author

                                      with 10 other contributors 


                    Simon Lin

Member since: 10/10/2019

344 Reputation

                                      1 Guide authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       Cal Poly, Team S11-G2, Regan Fall 2019                        

                                                  Member of Cal Poly, Team S11-G2, Regan Fall 2019 



                    CPSU-REGAN-F19S11G2                     


                                            5 Members                     


                                            37 Guides authored

Boushi Adams - Jun 18, 2020

Reply

This guide does show how to remove the trigger/bumper casing and board from the controller but does not show how to remove the triggers/bumpers from the casing they are in.

Alex Crocker - Feb 9, 2022

Yeah, this is a pretty big point to be missing, especially with the Flex Cable for the shoulder button inputs being right beside the post you need to pull out to remove the ZL and ZR buttons. Guidance on how to remove the post safely without damaging the cable would be great.

zusanu - Apr 8, 2022

https://youtu.be/vUpi_OEuPHw

Christian - Mar 7, 2022

Reply

Used the guide to repair a shattered right shoulder button successfully. Thanks!