Difficulty
Very easy
Steps
6
Time Required
5 minutes
Sections
1
- Battery
- 6 steps
Flags
0
BackNintendo Switch Pro Controller
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
The Switch Pro Controller uses JIS screws, but you can use a Phillips screwdriver in a pinch. Be very careful not to strip the screws. iFixit’s Phillips bits are designed to be cross-compatible with JIS-style screws.
NOTE: an improperly sync Switch Pro controller will not charge properly. To determine if your battery is faulty and needs replacing, you can first re-sync your controller and, while plugged in, check within the Switch controllers menu if it is charging properly.
CAUTION: The handling of any swollen batteries should be done with the utmost care. For information on how to identify, what to do with, how to handle, and how to dispose of swollen batteries follow the link below.
What to do with a swollen battery
What you need
Step 1
Remove the screws
- Flip the controller over so the model stickers face the ceiling.
- Use a JIS 00 driver or an official iFixit PH 00 driver to remove the two black flathead 8.4 mm-long screws that secure the handles, located at the ends of the handles.
Flip the controller over so the model stickers face the ceiling.
Use a JIS 00 driver or an official iFixit PH 00 driver to remove the two black flathead 8.4 mm-long screws that secure the handles, located at the ends of the handles.
1024
Step 2
Remove the handle covers
- Carefully remove the handle covers by pulling them away from the main body.
Carefully remove the handle covers by pulling them away from the main body.
Step 3
Remove the screws
- Use a Phillips screwdriver to remove the four silver 6.8 mm-long screws that secure the clear back plastic cover.
Use a Phillips screwdriver to remove the four silver 6.8 mm-long screws that secure the clear back plastic cover.
Step 4
Unclip the plastic cover
- Carefully pry away the clear plastic cover using your fingernail.
Carefully pry away the clear plastic cover using your fingernail.
Step 5
Remove the clear plastic cover
- Remove the clear plastic cover.
Remove the clear plastic cover.
Step 6
Remove the battery
- Remove the lithium-ion battery by using a fingernail or plastic opening tool to pry it up on the left side.
- Only a small amount of force is needed.
Remove the lithium-ion battery by using a fingernail or plastic opening tool to pry it up on the left side.
Only a small amount of force is needed.
To reassemble your device, follow these instructions in reverse order.
For optimal performance, calibrate your newly installed battery after completing this guide.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.
Cancel: I did not complete this guide.
18 other people completed this guide.
Author
with 14 other contributors
Daniel Tagalog
Member since: 10/10/2019
1,165 Reputation
3 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team S11-G2, Regan Fall 2019
Member of Cal Poly, Team S11-G2, Regan Fall 2019
CPSU-REGAN-F19S11G2
5 Members
37 Guides authored
Seani M - Apr 8, 2020
Reply
now what after taking the battery out
frzno72 - Dec 21, 2020
Install the replacement battery and follow the steps in reverse order…
Dan Carroll - May 19, 2021
Reply
easy peasy only have to recycle battery
smol_tsukiko - Jul 4, 2022
Reply
Where can I buy genuine ctr-003 batteries in germany/europe?
Unthar - Oct 14, 2022
Reply
My controller would not turn on one day. Followed this guide to remove the battery and just reseat it . Works now! Thank you!