Nintendo Switch Micro Sd Card Reader Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 - 10 minutes

Sections

Rear Panel
8 steps
Micro SD Card Reader
2 steps

Flags

BackNintendo Switch
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

The Switch uses JIS screws, but you can use a Phillips screwdriver in a pinch. Be very careful not to strip the screws. iFixit’s Phillips bits are designed to be cross-compatible with JIS-style screws.

WARNING: The battery cannot be disconnected during this repair, so make sure to only use ESD-safe tools and be extra careful when using any metal tools. Not doing so could short a connection and damage the device.

Note: This guide, and the part we sell, are compatible with the original Nintendo Switch model released in 2017, as well as the newer refreshed model released in 2019 (model numbers HAC-001 and HAC-001(-01), respectively).

What you need

Step 1

              Release the Joy Con controller locking tabs

Before you begin this repair, make sure the device is completely powered off.
Press and hold down the small round button on the back of the Joy Con controller.
While you hold down the button, slide the controller upward.

Before you begin this repair, make sure the device is completely powered off.

Press and hold down the small round button on the back of the Joy Con controller.

While you hold down the button, slide the controller upward.

1024

Step 2

              Remove the Joy Con controllers

Continue sliding the Joy Con upward until it’s completely removed from the console.
Repeat this same process for the other Joy Con.

Continue sliding the Joy Con upward until it’s completely removed from the console.

Repeat this same process for the other Joy Con.

Step 3

              Remove the back-side screws

Use a Y00 screwdriver to remove the four 6.3 mm-long screws securing the rear panel.
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

Use a Y00 screwdriver to remove the four 6.3 mm-long screws securing the rear panel.

Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

Step 4

              Remove the top and bottom screws

Use a JIS 000 driver or an official iFixit PH 000 driver to remove the following screws securing the rear panel:
One 2.5 mm-long screw on the top edge of the device
Two 2.5 mm-long screws on the bottom edge of the device
To prevent these tight screws from stripping, apply firm downward force, work slowly and try another JIS 000 or PH 000 driver if the screws won’t come out.

Use a JIS 000 driver or an official iFixit PH 000 driver to remove the following screws securing the rear panel:

One 2.5 mm-long screw on the top edge of the device

Two 2.5 mm-long screws on the bottom edge of the device

To prevent these tight screws from stripping, apply firm downward force, work slowly and try another JIS 000 or PH 000 driver if the screws won’t come out.

Step 5

Use a JIS 000 screwdriver or an official iFixit PH 000 driver to remove the two 3.8 mm center screws on the sides of the device (one on each side).

Use a JIS 000 screwdriver or an official iFixit PH 000 driver to remove the two 3.8 mm center screws on the sides of the device (one on each side).

Step 6

Use your finger to flip up the kickstand on the back of the device.
If there’s a microSD card in the microSD card slot, remove it now before you continue to the next step.

Use your finger to flip up the kickstand on the back of the device.

If there’s a microSD card in the microSD card slot, remove it now before you continue to the next step.

Step 7

Use a JIS 000 screwdriver or an official iFixit PH 000 driver to remove the 1.6 mm screw in the kickstand well.
Close the kickstand.

Use a JIS 000 screwdriver or an official iFixit PH 000 driver to remove the 1.6 mm screw in the kickstand well.

Close the kickstand.

Step 8

Open the game card cartridge flap.
The game card cartridge flap attaches to the other half of the plastic shell, preventing you from completely lifting up the rear panel if it’s closed.
Lift the rear panel up from the bottom of the device and remove it.

Open the game card cartridge flap.

The game card cartridge flap attaches to the other half of the plastic shell, preventing you from completely lifting up the rear panel if it’s closed.

Lift the rear panel up from the bottom of the device and remove it.

Step 9

              Remove the microSD card reader

Use a JIS 000 screwdriver or an official iFixit PH 000 driver to remove the 3.1 mm screw securing the microSD card reader to the device.

Use a JIS 000 screwdriver or an official iFixit PH 000 driver to remove the 3.1 mm screw securing the microSD card reader to the device.

Step 10

Use your fingers or a pair of tweezers to lift the microSD card reader straight up from the device to disconnect and remove it.
During reassembly, make sure the press connector underneath the foam pad is firmly connected to the motherboard. It may help to remove the foam pad before reinstalling the card reader.

Use your fingers or a pair of tweezers to lift the microSD card reader straight up from the device to disconnect and remove it.

During reassembly, make sure the press connector underneath the foam pad is firmly connected to the motherboard. It may help to remove the foam pad before reinstalling the card reader.

Compare your new replacement part to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Nintendo Switch Answers community for help.

Cancel: I did not complete this guide.

                                                                                      108 other people completed this guide.

Author

                                      with 6 other contributors

                    Craig Lloyd

Member since: 02/10/2016

28,344 Reputation

                                      82 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges

Finx O’Mally - Feb 4, 2019

My SD reader never worked.

Used this guide to find that it was never seated correctly. Reseated and now works perfectly. THANK YOU!

Ewan MacInnis - Mar 31, 2019

My console won’t boot if I have an SD card inserted after reseating it. What should I do?

Nicola Bonardi - Apr 25, 2019

Easy guide, fixed my problem. Changed the SD card reader cause I was abusing of it by putting SD in and out constantly.

Matt - Jul 12, 2019

Great guide! My 11-year-old son was able to fix his Switch himself with no difficulty.

Philip Milian - Jul 22, 2019

Some one can help me, when I tried to put the connector again I damage the fpc connector of the motherboard so I try to find out again can any one know the kind of model of this connector I really appreciate the help

Best regards

Introduction#

What you need#

Introduction

What you need