Nintendo Game Boy Advance Sp Buttons Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Battery
3 steps
Back Cover
2 steps
Motherboard
2 steps
Removing the Trackpads
1 step
Buttons
1 step

Flags

BackGame Boy Advance SP
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Use a standard Phillips #00 screwdriver to loosen the 4 mm screw that keeps the battery cover attached to the device.

Use a standard Phillips #00 screwdriver to loosen the 4 mm screw that keeps the battery cover attached to the device.

1024

Step 2

Lift the battery cover up and remove it from the device.
The screw will remain attached to the battery cover because of Nintendo’s design.

Lift the battery cover up and remove it from the device.

The screw will remain attached to the battery cover because of Nintendo’s design.

Step 3

Use your fingers or a plastic opening tool to remove the battery from the device.
Caution: Please exercise caution when handling the battery. If it appears to be swelling or damaged at all it is considered a fire hazard.

Use your fingers or a plastic opening tool to remove the battery from the device.

Caution: Please exercise caution when handling the battery. If it appears to be swelling or damaged at all it is considered a fire hazard.

Step 4

              Back Cover

Remove four 6.5 mm screws from the corners of the back cover using a tri-point Y00 screwdriver.
Remove two 4.6mm screws from the top-center and bottom-center of the device using a tri-point Y00 screwdriver.

Remove four 6.5 mm screws from the corners of the back cover using a tri-point Y00 screwdriver.

Remove two 4.6mm screws from the top-center and bottom-center of the device using a tri-point Y00 screwdriver.

Step 5

Lift the back cover off of the device.
Potential for device damage: These inner components are vulnerable to static electricity. Exercise caution when handling these next steps to prevent damaging the device.
Look out for the power switch that can fall out when taking the back cover off.

Lift the back cover off of the device.

Potential for device damage: These inner components are vulnerable to static electricity. Exercise caution when handling these next steps to prevent damaging the device.

Look out for the power switch that can fall out when taking the back cover off.

Step 6

              Motherboard

Using a Phillips #00 screwdriver, remove the three Phillips #00 4 mm long screws that hold the motherboard to the button panel.

Using a Phillips #00 screwdriver, remove the three Phillips #00 4 mm long screws that hold the motherboard to the button panel.

Step 7

Be careful not to tear the ribbon cable that’s connected to the screen. If you tear it, games will not appear on the device’s screen!
Flip the motherboard up and rest it on the other half of the device, so that the back of the buttons are visible as seen in the picture.

Be careful not to tear the ribbon cable that’s connected to the screen. If you tear it, games will not appear on the device’s screen!

Flip the motherboard up and rest it on the other half of the device, so that the back of the buttons are visible as seen in the picture.

Step 8

              Removing the Trackpads

Using your fingers, gently lift and remove the trackpads covering the following:
‘A’ and ‘B’ buttons
Directional Control Button Pad
‘Start’ and ‘Select’ buttons

Using your fingers, gently lift and remove the trackpads covering the following:

‘A’ and ‘B’ buttons

Directional Control Button Pad

‘Start’ and ‘Select’ buttons

Step 9

              Buttons

Using tweezers or fingers, lift and remove:
‘A’ and ‘B’ buttons
Directional control button pad
‘Start’ and ‘select’ buttons

Using tweezers or fingers, lift and remove:

Directional control button pad

‘Start’ and ‘select’ buttons

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      9 other people completed this guide.

Author

                                      with 8 other contributors

                    Jose Bautista

Member since: 01/11/2013

600 Reputation

                                      1 Guide authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 17-22, Forte Winter 2013                        

                                                  Member of Cal Poly, Team 17-22, Forte Winter 2013 



                    CPSU-FORTE-W13S17G22                     


                                            4 Members                     


                                            33 Guides authored

Jikan - Mar 12, 2017

Hi,

How do I fix my SP Brighter when A and B buttons are simultaneously pressed, the system turns off? Please Help! Thank you in advance!

Taahaco 2005 - Jun 2, 2018

there is most likely a crack in the mother board or the battery has too much pressure placed onto it

you can fix this by changing the position of the battery and putting something to stop it from moving around so it fits tightly

アラン - Jul 27, 2022

HI there! My problem is that I have to press the button A harder for the action to be registered, how can I fix that?

Introduction#

What you need#

Team#

Introduction

What you need

Team