Nintendo Dsi Xl Power Board Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          15 - 30 minutes            

Sections

3

• Battery
• 2 steps
• Lower Case
• 5 steps
• Power Board
• 3 steps

Flags

0

• BackDSi XL

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Remove the two Phillips screws securing the battery cover to the back of the handheld console.
• Lift the battery cover off the back of the DSi XL.

Remove the two Phillips screws securing the battery cover to the back of the handheld console.

Lift the battery cover off the back of the DSi XL.

1024

Step 2

• Lift the battery from the DSi XL.

Lift the battery from the DSi XL.

Step 3

              Lower Case               

• Remove the four rubber screw covers on the lower case by prying them up with a push pin.

Remove the four rubber screw covers on the lower case by prying them up with a push pin.

Step 4

• Remove the following seven Phillips screws that secure the lower case to the rest of the DSi XL:
• Four silver 5.3 mm screws
• Two black 5.3 mm screws
• One black 2.5 mm screw

Remove the following seven Phillips screws that secure the lower case to the rest of the DSi XL:

Four silver 5.3 mm screws

Two black 5.3 mm screws

One black 2.5 mm screw

Step 5

• Turn the DSi XL over, and open the display.
• Insert a spudger between the upper and lower case at the bottom left corner of the DSi.
• Slide the spudger along the bottom edge of the upper case to release the latches securing the upper case to the lower case.

Turn the DSi XL over, and open the display.

Insert a spudger between the upper and lower case at the bottom left corner of the DSi.

Slide the spudger along the bottom edge of the upper case to release the latches securing the upper case to the lower case.

Step 6

• Close the display and turn the DSi XL over.
• Lift the lower case from the front edge.
• Rotate the lower case away from the DSi.
• The lower case cannot be completely removed yet, since it is still connected to the motherboard.

Close the display and turn the DSi XL over.

Lift the lower case from the front edge.

Rotate the lower case away from the DSi.

The lower case cannot be completely removed yet, since it is still connected to the motherboard.

Step 7

• Using a spudger, pry the SD card/right shoulder button connector off its socket.
• Pry the volume button/left shoulder button connector off its socket on the motherboard with a spudger.

Using a spudger, pry the SD card/right shoulder button connector off its socket.

Pry the volume button/left shoulder button connector off its socket on the motherboard with a spudger.

Step 8

              Power Board               

• Using the flat end of a spudger, flip up the retaining flap on the ZIF connector for the D-pad/power button cable.
• With the pointed end of the spudger, pull the D-pad/power button cable from its connector on the motherboard.

Using the flat end of a spudger, flip up the retaining flap on the ZIF connector for the D-pad/power button cable.

With the pointed end of the spudger, pull the D-pad/power button cable from its connector on the motherboard.

Step 9

• Using the flat end of the spudger, carefully pry the battery cable out of its socket on the motherboard.
• Use caution, as the wires are very fragile and could come out of the connector if pulled on too hard.

Using the flat end of the spudger, carefully pry the battery cable out of its socket on the motherboard.

Use caution, as the wires are very fragile and could come out of the connector if pulled on too hard.

Step 10

• Remove the seven 2.5 mm silver screws securing the power board to the upper case.
• Lift the power board off the upper case.

Remove the seven 2.5 mm silver screws securing the power board to the upper case.

Lift the power board off the upper case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.                                             

Author

                                      with 7 other contributors 

                    Brett Hartt                     

Member since: 04/12/2010

125,280 Reputation

                                      143 Guides authored                  



                       Badges:
                       52







                                                        +49 more badges                           

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored