Difficulty

Moderate

Steps

9

Time Required

Suggest a time??

Sections

3

  • Battery
  • 2 steps
  • Lower Case Assembly
  • 4 steps
  • Stylus Housing
  • 3 steps

Flags

0

  • BackDSi

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Unscrew the two Phillips screws securing the battery cover to the lower case.
  • The screws remain captive to the battery cover.
  • Grasp the battery cover and lift out of the lower case.

Unscrew the two Phillips screws securing the battery cover to the lower case.

The screws remain captive to the battery cover.

Grasp the battery cover and lift out of the lower case.

1024

Step 2

  • Wedge the edge of a spudger in between the top of the battery and its lower case housing and pry upwards to dislodge the battery.
  • Grasp the battery and remove it from the DSi.

Wedge the edge of a spudger in between the top of the battery and its lower case housing and pry upwards to dislodge the battery.

Grasp the battery and remove it from the DSi.

Step 3

              Lower Case Assembly
  • Two screws are hidden underneath two rubber feet highlighted in red.
  • Use the tip of a spudger to pry the rubber feet out of the lower case.

Two screws are hidden underneath two rubber feet highlighted in red.

Use the tip of a spudger to pry the rubber feet out of the lower case.

Step 4

  • Remove the following screws securing the lower case to the body of the DSi:
  • Six 5.2 mm Phillips #00 screws.
  • One 2.7 mm Phillips #00 screw.

Remove the following screws securing the lower case to the body of the DSi:

Six 5.2 mm Phillips #00 screws.

One 2.7 mm Phillips #00 screw.

Step 5

  • Insert the spudger in between the lower casing and lower panel near the top right corner of the DSi.
  • Carefully run the spudger along the edge of the outer casing, creating an opening between the body and the casing.
  • Continue running the spudger around the body of the DSi until the majority of the lower case has been separated.

Insert the spudger in between the lower casing and lower panel near the top right corner of the DSi.

Carefully run the spudger along the edge of the outer casing, creating an opening between the body and the casing.

Continue running the spudger around the body of the DSi until the majority of the lower case has been separated.

Step 6

  • Carefully lift the lower casing from its bottom edge.
  • The lower case is still attached to the motherboard by the volume and SD board cable highlighted in red. Do not try to completely remove the lower case of the DSi yet.
  • Pry the volume and SD board cable up from its socket on the motherboard using a spudger.
  • Once the cable is completely removed, then you may take off the entire outer casing.

Carefully lift the lower casing from its bottom edge.

The lower case is still attached to the motherboard by the volume and SD board cable highlighted in red. Do not try to completely remove the lower case of the DSi yet.

Pry the volume and SD board cable up from its socket on the motherboard using a spudger.

Once the cable is completely removed, then you may take off the entire outer casing.

Step 7

              Stylus Housing
  • Pull the stylus straight out its housing and remove it from the rear case.

Pull the stylus straight out its housing and remove it from the rear case.

Step 8

  • Remove the five 3.9 mm Phillips screws securing the stylus holder to the rear case.

Remove the five 3.9 mm Phillips screws securing the stylus holder to the rear case.

Step 9

  • Lift and remove the left plastic protector from the DSi’s rear case.
  • Grasp the stylus holder from the left side and lift upwards to remove it from the DSi.

Lift and remove the left plastic protector from the DSi’s rear case.

Grasp the stylus holder from the left side and lift upwards to remove it from the DSi.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 2 other contributors 


                    Walter Galan

682,038 Reputation

                                      1,203 Guides authored                  



                       Badges:
                       54







                                                        +51 more badges