Difficulty
Easy
Steps
11
Time Required
10 minutes
Sections
4
- Battery
- 3 steps
- Back Panel
- 2 steps
- Motherboard replacement.
- 5 steps
- Bottom LCD Screen
- 1 step
Flags
0
BackDS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the cartridge from the console.
- Use a Phillips #00 Screwdriver to remove the screw securing the battery door to the rear case.
- Remove the battery door.
- In the images, it shows that the fixer is using a flathead screwdriver. This flathead screwdriver will work just like the Phillips #00 Screwdriver.
Remove the cartridge from the console.
Use a Phillips #00 Screwdriver to remove the screw securing the battery door to the rear case.
Remove the battery door.
In the images, it shows that the fixer is using a flathead screwdriver. This flathead screwdriver will work just like the Phillips #00 Screwdriver.
1024
Step 2
- Use a plastic opening tool or spudger to pry out the battery from the bottom. If a plastic opening tool or spudger isn’t available, your fingernails may work.
Use a plastic opening tool or spudger to pry out the battery from the bottom. If a plastic opening tool or spudger isn’t available, your fingernails may work.
Step 3
- Remove the battery from the Nintendo DS.
Remove the battery from the Nintendo DS.
Step 4
Back Panel
- Remove the seven Y00 screws located on the back.
- If your DS has a lanyard attached to it, you can remove it to make the process of opening the top-left screw easier.
Remove the seven Y00 screws located on the back.
If your DS has a lanyard attached to it, you can remove it to make the process of opening the top-left screw easier.
Step 5
- With your hands, pry the back panel off the main case.
- Separate the back from the front, and set it aside.
With your hands, pry the back panel off the main case.
Separate the back from the front, and set it aside.
Step 6
Motherboard replacement.
- Using a Phillips #00 screwdriver, remove the four screws on the circuit board.
- Be careful NOT to slip with the screwdriver, you can damage the circuit board!
Using a Phillips #00 screwdriver, remove the four screws on the circuit board.
Be careful NOT to slip with the screwdriver, you can damage the circuit board!
Step 7
- Unlock the two large ribbon cables by moving the black clip up.
- Carefully pull the ribbon cables down and out with your fingers.
- Do not use pliers to pull the cables, as they can be damaged easily.
Unlock the two large ribbon cables by moving the black clip up.
Carefully pull the ribbon cables down and out with your fingers.
Do not use pliers to pull the cables, as they can be damaged easily.
Step 8
- Locate the two small ribbon cables, beneath the rightmost large ribbon cable.
- Slide the locks for the small ribbon cables down to the side, and remove the cables.
- It may be useful to use tweezers to remove the small ribbon cables.
- Be careful not to damage the delicate ribbon cables.
Locate the two small ribbon cables, beneath the rightmost large ribbon cable.
Slide the locks for the small ribbon cables down to the side, and remove the cables.
It may be useful to use tweezers to remove the small ribbon cables.
Be careful not to damage the delicate ribbon cables.
Step 9
- Locate the Wifi antenna pigtail connector.
- Remove the antenna by grasping it at the head with tweezers. Using a slight rocking motion, pull up to dislodge the connector.
Locate the Wifi antenna pigtail connector.
Remove the antenna by grasping it at the head with tweezers. Using a slight rocking motion, pull up to dislodge the connector.
Step 10
- Feed the ribbon cables through the opening on the board.
- Pull up and remove the circuit board, and set it aside.
Feed the ribbon cables through the opening on the board.
Pull up and remove the circuit board, and set it aside.
Step 11
Bottom LCD Screen
- Peel off the black cushion foam on the bottom touch screen to expose the ribbon cable.
- Gently lift the screen out of the base.
Peel off the black cushion foam on the bottom touch screen to expose the ribbon cable.
Gently lift the screen out of the base.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
21 other people completed this guide.
Author
with 7 other contributors
dnguye26
Member since: 10/28/2009
676 Reputation
4 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 18-3, Maness Fall 2009
Member of Cal Poly, Team 18-3, Maness Fall 2009
CPSU-MANESS-F09S18G3
4 Members
20 Guides authored
Zackary Benton - Sep 7, 2017
Reply
I like it but add a step 12 maybe, to see how to put in a new screen.